Will 331-TPSI-001 Universal Mounting Panel for Redarc Tow-Pro Fit In Hole Where Lighter Fits

Question

Question:

I was wondering if I could take out the cigarette lighter on my 05 Ram 2500 and put the Universal Mounting Panel for Redarc tow-pro in its place?

asked by: Brandon

0

Expert Reply:

Oddly enough I wasn't able to find the diameter of the hole for a cigarette lighter, but I can tell you the hole diameter. The instructions for the Redarc # 331-TPSI-001 Universal Mounting Panel include a drilling template which shows the mounting hole as being 1 inch in diameter.

So, if the hole for your cigarette lighter is 1 inch in diameter, you'll be good to go. I've linked those instructions for you.

expert reply by: Mike L

0

Answer 1

When the LED light on the Curt Echo part #C51180 does not illuminate that means the brake controller is not getting power from the 12V pin or the ground is bad. On a 7-way trailer connector, the 12V power function does not need to be connected for…

view full answer...

Answer 2

You will still be able to use the trailer with the 4-Way after installing the 4 to 5-Way adapter, #20036. First, you could just remove the adapter if you wanted to and then plug in the 4-Way like normal while stowing the adapter in the truck. The…

view full answer...

Answer 3

When it comes to your 5 wires on your 4 wire pin and you're wanting to run your trailer brakes I recommend switching the 4 flat to The Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires #ETBC7. This…

view full answer...

Answer 4

To answer your first question, it is possible to splice the brake controller's 12 volt power wire into the 12 volt power wire you have attached to the vehicle's battery to charge the trailer's battery but this is certainly not recommend.…

view full answer...

Answer 5

From previous customers we have determined that your 2021 Coleman Lantern 17B has 3,500 lb trailer axles so for replacement assemblies you'd want the #AKEBRK-35-SA for a self adjusting set. This includes everything like you said you were…

view full answer...

Answer 6

It is normal to have continuity between the brake(blue) wire and ground(white) wire. The electric trailer brake is an electromagnet when it has power it attracts to the steel inside the hub/drum. If you are having issues with your trailer brakes…

view full answer...

Answer 7

You should have continuity between the 5 o'clock brake output pin and 7 o'clock ground pin in your 7-way connector with the brakes applied. I recommend turning the trailer brake controller to its max setting and having someone apply the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will 331-TPSI-001 Universal Mounting Panel for Redarc Tow-Pro Fit In Hole Where Lighter Fits

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching