CIPA CM01139 Adustable Side Mirrors for Kubota 1120D UTV

Question

Question:

I did not see any feedback on the Kubota UTVs. I have an 1120 D.

asked by: Dave F

0

Expert Reply:

I'm not certain what you mean by 'feedback', but the CIPA # CM01139 isn't a vehicle specific item. It will mount to round roll cage tubing that are 1-3/4 inches in diameter. If your roll cage uprights are of that diameter, the mirrors will work great for you.

As you can see from the provided product reviews, this mirror set gets good reviews from our customers.

expert reply by: Mike L

0

Answer 1

The CIPA Adjustable Side Mirrors for UTVs #CM01139 are designed to fit on round roll cage bars that are 1-3/4" diameter, so as long as your John Deere XUV865M has that diameter bars on the front of the roll cage, they will fit. If you're…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Daniel congrats on the new truck! The Lomax Stance Hard Tonneau Cover item #LOM54RV does indeed fit the 2026 Chevrolet Silverado EV with the Mid Gate. It also works with the Multi-Flex Tailgate that comes on the Trail Boss models. For a…

view full answer...

Answer 9

Hey Al, welcome back. You are on the right track here. The Replacement Base for B&W Companion OEM 5th Wheel Trailer Hitch #BWRVB3710 will drop directly into the puck system in your 2024 Silverado 2500 HD. All of the Companion hitches use the same…

view full answer...

Answer 10

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 11

Hey Danny, this is a really great question but B and W states that their fifth wheel to gooseneck adapters like the part #BW83RV actually put less stress on the RV frame than a pin box so the warranty would not be affected. Lippert might take a…

view full answer...

Answer 12

Hey Edwin! If the listed dry tongue weight is 1,330 lbs you will likely be over the rating of your current SwayPro spring bars. You'll probably be adding 150-200 lbs with the propane and batteries, but that does depend on the number of propane…

view full answer...

CIPA CM01139 Adustable Side Mirrors for Kubota 1120D UTV

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching