Replacing the GS961LP with the Atwood LP Gas Detector RV 12V White 36719

Question

Question:

I have the GS961 LP, and it looks like the Atwood LP Gas Detector RV 12V White 36719 will fit in its space even though it is claimed to Replace the 36720. Will this work?

asked by: Josh T

0

Expert Reply:

I spoke with a contact at Atwood. The main concern for the GS961LP is ensuring that it receives 12V power. Because the Atwood LP Gas Detector RV 12V White 36719 has this, it's highly possible that it can work for you.

However, we do not sell this part, so I cannot 100% confirm this. We can confirm the # AT36681 that you referenced, so I recommend going with that.

expert reply by: Kef G

0

Answer 1

You could use the 2-wire Propane Gas and Carbon Monoxide Detector part #RS34FR in place of the Atwood 36681 that you referenced. This would fit in the cut out you have now and has a flange that is large enough that would cover the hole.

view full answer...

Answer 2

Hey Wayne, to replace the Atwood propane gas detector you have now you could use the part #AT36681 which also is a carbon monoxide detector.

view full answer...

Answer 3

We have exactly what you are looking for. You will want the Atwood combination gas and carbon monoxide detector #AT36681.

view full answer...

Answer 4

The Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 is going to be the closest replacement to your ProTECHtor GS961LP-RV. It requires a 3-9/16" long x 3-7/16" wide x 1" deep cutout hole and will alert you to both unsafe…

view full answer...

Answer 5

I wasn't able to find the Atwood 36720 RV Propane Gas Detector you mention, however I was still able to find the RV Propane Gas Detector #RS64FR in white, or #RS44FR in black to work as a replacement for your Protechtor Series 2001 LP Gas…

view full answer...

Answer 6

Attached is a wiring diagram for the Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681. You only have to connect the black wire and one red wire, but the second red wire is for backup power which is a good idea just so you know the alarm…

view full answer...

Answer 7

Yes, the Paddle Handle Latch #PLR5115 does come with the release knob that you seen in the picture for the interior of the door.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacing the GS961LP with the Atwood LP Gas Detector RV 12V White 36719

Continue Researching