Is it Safe to Flip the 10 Hole Cushioned Pintle Mounting Bar and Use The Top Set Of Holes To Tow
Published 08/04/2009
Question:
i have an 8 hole adaptor now and it is fliped upside down with the pintle all the way up in order to level the trailer out. well i have no further adjustment and was thinking about getting a 10 hole adaptor. is it ok to have it fliped so the holes go up instead of down? i just want to make sure its safe.
asked by: Jay
Expert Reply:
Yes, it is okay to use the 10 hole Cushioned Pintle Mounting Bar, part number AMPC3, in the rise position and use the top four holes to mount your ring, as long as you stay within the weight rating of the ring, mounting bar, hitch and towing vehicle, whichever is the lowest capacity.
Product Page this Question was Asked From
Convert-A-Ball Cushioned, Adjustable Pintle Mounting Bar for 2" Hitches - 10 Holes - 10,000 lbs
- Pintle Hitch
- Mounting Plate Only
- Adjustable Height
- 10000 lbs GTW
- 2 Inch Hitch Mount
- 10 Holes
- Cushioned Shank
- Convert-A-Ball
more information >
Continue Researching
- Shop: Trailer Hitch
- Shop: Brake Controller
- Shop: Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 25-7/8" Lift - 10K
- Shop: Suspension Enhancement
- Shop: Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 28-3/4" Lift - 12K
- Search Results: weld on trailer jack
- Q&A: Can a Pintle Hook Mount be Used in the Rise and Drop Positions
- Video: Let’s Check Out the Wheel Masters Tire Pressure Valve Extenders
- Shop: Curt Pintle Hook Mounting Plate for 2-1/2" Hitches - 10-3/4" Shank - 8 Hole - 20,000 lbs
- Shop: B&W Pintle Hook Mounting Plate for 2" Hitches - 11" Shank - 8 Hole - 16,000 lbs
- Video: Feature Review B and W Pintle Hook Mounting Plate for 2" Hitches
- Video: Ultimate Overview of the Curt SecureLatch Adjustable Pintle Mounting Plate for 2" Hitches
- Shop: Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle
- Shop: Square Jack w/ Crank - Side Pin Drop Leg - Spring Return - 10K Lift - 25-3/4" Travel
- Shop: Curt SecureLatch Adjustable Pintle Mounting Plate for 2" Hitches - 20,000 lbs
- Video: A Closer Look at the B and W Pintle Hook Mounting Plate for 2" Hitches
- Search Results: curt secure latch
- Search Results: trailer door hinge
- Video: Checking Out the B and W Pintle Hook Mounting Plate for 2-1/2" Hitches
- Search Results: 2 inch ball pintle hitch
- Search Results: b&w pintle
- Search Results: pintle hitch
- Video: Ultimate Overview of the Conventional Ramp Door Spring for 8' Wide Enclosed Trailer
- Video: The Low-Down on the Conventional Ramp Door Spring for 7' Wide Enclosed Trailer
- Q&A: Do Electric Trailer Brakes Work in Forward and in Reverse
- Search Results: ramp door
- Q&A: What Is The Correct Oil To Use In My Dexter Axles With Oil Lube Bath Hubs?
- Q&A: Recommended Grease Conversion for Dexter 12k Oil Bath Axles
- Q&A: Can Ball Mounts Be Turned Upside Down To Increase Height
- Q&A: What Size Bolts are Used to Mount Convert-A-Ball Pintle Hook Combo # PH1