Troubleshooting Constant Red Light on Tekonsha Voyager Brake Controller

Question

Question:

The red light stays on tekonash voyager

asked by: Allen L

0

Expert Reply:

The red light on your Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional # 39510 shows that your unit is not leveled correctly for in the inertia sensor to work as designed. There is a process outlined in the attached video that shows this and I've also attached the installation instructions to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

That's a pretty odd issue to have with the Prodigy P3 part #90195. Try unplugging it for a few seconds and then plugging it back it as a hard reset might get it to work like it's supposed to.

view full answer...

Answer 2

There are a couple possible reasons why the green light on your Tekonsha Voyager Brake Controller #39510 is not turning red when applying the brakes in your tow vehicle. I first recommend testing the red wire from the controller with a circuit tester…

view full answer...

Answer 3

We actually sell a lock set for the ball mount platform of the Curt Rebellion XD #C83WR with the part #IR97FR. The diameter of the pins is 3/4 inch. The usable span of the locks is 2-7/8 inches.

view full answer...

Answer 4

There is one lock set I really like the most that is going to give you the best overall protection for the 15,000 lb capacity Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls #C83WR: - InfiniteRule Lock Set…

view full answer...

Answer 5

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 6

What you described is perfectly normal. When not connected to a trailer the Prodigy P2 part #90885 will show two dots like you described. After a period of inactivity the controller will go into sleep mode. It doesn't turn off with the vehicle…

view full answer...

Answer 7

Thanks for the well wishes! There are two primary differences between the original Tekonsha Prodigy and the newer Prodigy P2. The P2 will actuate electric over hydraulic trailer brakes, where the original Prodigy will not. The original Prodigy needed…

view full answer...

Answer 8

Adjusting the P2, #90885, is easy. Once you have it mounted according to the instructions, linked for reference, you will beginning setting up the power output. To do this take the truck and trailer to a flat level surface. Set the controller to 6…

view full answer...

Answer 9

According to the troubleshooting guide for the Tekonsha Voyager Trailer Brake Controller #39510 when there is no green light with the trailer connected then that means you either have corrosion on the trailer plug contact or you have a loss of power…

view full answer...

Answer 10

The green light of your Tekonsha Voyager Brake Controller part #39510 is to show that the brake controller senses a trailer being connected. If you can't get the green light to come on plus your brake output pin on your 7-way is reading full…

view full answer...

Answer 11

The flicker you are seeing on the brake output circuit of your vehicle is normal. Brake controllers will lightly pulse their output circuit to check to see if a trailer is connected due to the amperage draw of the brake magnets. So what this all…

view full answer...

Answer 12

I have something close but there are not Class 4 hitches available for your coach that I can find. Instead I recommend instead using the Curt Adjustable Width Trailer Hitch Receiver for RVs part #13703. While it is not a Class 4 hitch it does allow…

view full answer...

Troubleshooting Constant Red Light on Tekonsha Voyager Brake Controller

Featured Help Information

Miscellaneous Media

Continue Researching