Replacement Shroud for Coleman Mach RV Unit 7330-714

Question

Question:

I have a coleman part 7330-714 I see your number is a 713 is it different

asked by: Craig P

0

Expert Reply:

I pulled up a Coleman RV AC unit 7330-714 and it is a Mach style unit like what the part # MA00-325001 you referenced is designed to fit so this would be the correct replacement.

expert reply by: Jameson C

0

Answer 1

I could not locate anything specifically from the STP-015-MR226-09 number. It looks like that may be an OEM part number for whoever manufactured your RV. From the little information I could find, it looks like it may be the OEM equivalent of the…

view full answer...

Answer 2

The Thetford Aqua Magic V RV Toilet 31684 has a rough-in of 7-5/8". This is unfortunately not a lot of space so most of your newer toilets will not fit. The rough-in is simply the distance from the center of the floor opening to the wall. The…

view full answer...

Answer 3

Hello John; with that part number it sounds like you have the Coleman-Mach 7330-714. The correct replacement shroud would be the #MA00-325001. Take a look at the measurements in the diagrams below and compare that to what you have now to see if it…

view full answer...

Answer 4

Hey Brian, I checked with Dexter and wasn't able to get anything off of that 5514706 number you gave me. If you could email me directly a picture of your axle tag I can see if we have a replacement that way. Just respond to the address you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Shroud for Coleman Mach RV Unit 7330-714

Featured Help Information

Miscellaneous Media

Continue Researching