Can You Get the Lippert Electric Stabilizer Jack Without the Motor?

Question

Question:

Can you purchase Lippert electric jacks without the motor

asked by: Jimmy F

0

Expert Reply:

The Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707 or # LC369774 only come with the motor. You can get a replacement motor and replacement arms but the main support beam and legs are not replacement parts available. If you want a similar style jack without a motor you can use the Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs # UF39-941704.

expert reply by: Jason S

0

Answer 1

Even though the 337199 has been discontinued there's still quite a few out there on the market so you could still get an exact replacement with the Lippert High-Speed Power Stabilizer Jack - 30" Lift LC337199 or swap to their other model,…

view full answer...

Answer 2

Yes, the Lippert High-Speed Power Stabilizer Jack #LC298707 is a direct replacement. This is actually the same as the 337199 but with the switch kit.

view full answer...

Answer 3

If you want to use the Redarc Tow-Pro Elite Trailer Brake Controller - 2 Braking Modes - 1 to 3 Axles - Proportional #RED44FR, you will need the Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers #RED39FR

view full answer...

Answer 4

Curt has a recommended setup procedure outlined for the Curt Echo part #C51180 that is outlined in their install instructions for this controller but since not all trailer brakes apply the same way there isn't a standard setting you can use that…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hello David, great question. So, there is a chance that you will have to enlarge the access holes for the both the etrailer #e98912 hitch and the EcoHitch #306-X7365. Both hitches come with the same size spacers. The picture below will help…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Can You Get the Lippert Electric Stabilizer Jack Without the Motor?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching