Recommended Cover for NuCamp TAB 400 Trailer

Question

Question:

I am looking for a cover that will fit my NuCamp T@B 400 camper.

asked by: Peter D

0

Expert Reply:

It looks like most NuCamp Tab 400 trailers are roughly 219" long (18'-3") so the Classic Accessories # CA80200 would be the best available cover for your trailer. This provides good protection from UV rays and weather, plus the zippered panels help make it easier to get into the trailer when the cover is installed.

If your trailer is smaller than 18 feet long, let me know what the dimensions are and I can help you locate a cover that will fit a bit better.

expert reply by: Erik B

0

Rjumpteen

1/6/2026

Classic Accessories PolyPro III Deluxe RV Cover for R-Pod Trailers up to 17' 7" Long - Gray Part Number: CA80200 lol I thought that 17'7" was SHORTER than 18'3"... easy to put larger cover on smaller camper but not so much a smaller cover on a larger camper... what am I missing that you recommended a shorter length cover for a longer length camper?

Gwendolyn Y.

1/6/2026

@Rjumpteen The Classic Accessories PolyPro III Deluxe RV Cover part # CA80200 is made to cover trailers that are 20' long (covers 17' 7" trailer body only). Its a little confusing how Classic lists their covers. There are a few diagrams on the product page explaining a bit more.

Answer 1

For your 2021 Nucamp Tab 400 Boondocks Edition I recommend the Classic Accessories Deluxe PolyPro III HD Cover for R Pod Trailer - Up to 20' Long Item #CA80200. This provides good protection from UV rays and weather, plus the zippered panels help…

view full answer...

Answer 2

Thanks for the picture Chris! The lift-brackets mount about 29" back from the center of the coupler on the Blue Ox SwayPro Weight Distribution w/ Sway Control item #BXW0553. It looks like your trailer's tongue isn't going to have…

view full answer...

Answer 3

The Timbren Axle-Less Trailer Suspension #ASR5200S01 is going to be our only style replacement axle for your 2024 Nucamp Tab 400 BD. This uses a rubber spring suspension which is going to be independent from the left to the right. With your Tab…

view full answer...

Answer 4

Hi Alex; the gauge on the Big Truck Big RV Tongue Weight Scale for Trailers #BTBRV004 has a +/- 5% full scale accuracy and displays weight in 20-lb increments up to 1,000 lbs. We also have it available with a SnapPad #BTBRV99FR. If you want something…

view full answer...

Answer 5

The best way to prevent a vehicle like your 2018 Toyota Tacoma from sagging is with the use of a weight distribution system. What happens when you tow is that weight gets transferred to the rear axle of your tow vehicle which causes it to sag. A…

view full answer...

Answer 6

The main difference between a friction bar sway control unit like #17200 and an electronic unit is when they will operate on the trailer sway. The friction units work to stop the trailer from swaying while the electronic systems must wait for sway to…

view full answer...

Answer 7

The calibration or adjustment process of the Tow Pro Liberty part #RED24FR isn't quite the same as the standard brake controllers like you mentioned. Basically Redarc recommends a more vague process of starting with a low output and then ramping…

view full answer...

Answer 8

You ask an interesting question. If your 2017 Jeep Grand Cherokee has the factory-installed trailer sway control (TSC) system already and you are also using a mechanical weight distribution/sway control hitch system I do not recommend adding a third…

view full answer...

Answer 9

For your 2017 Toyota Tacoma the correct SumoSpring kit is the part #SSR-612-47 and not the kit you mentioned as that is for the older models. This will reduce the sag but what you might be better off with is a weight distribution system since that…

view full answer...

Answer 10

I took a look at the owner's manual for your 2018 Toyota Tacoma 6 Cylinder with the tow package and Toyota mentions that if the trailer being towed is above 2000lbs that a sway control system is required. I would go ahead and install sway control…

view full answer...

Answer 11

The ball you're referencing on your trailer tongue is most likely the one that would come with a friction sway control bar like the Curt Friction Sway Control for Weight Distribution Systems #17200. I'm assuming you most likely don't…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Recommended Cover for NuCamp TAB 400 Trailer

Product Page this Question was Asked From

Continue Researching