Replacement Hardware for Draw-Tite Trailer Hitch 75758

Question

Question:

two bolts came off trail bracket 9/16 inch carriage bolts do you have/? Draw Tite # 75758

asked by: Mark S

0

Expert Reply:

We do carry replacement hardware for the Draw-Tite Trailer Hitch Receiver # 75758, though just two bolts by themselves are not available, as you'll need the entire hardware kit with the Replacement Hardware Kit for Trailer Hitches # RHK.

To order it, just click # RHK, enter "75758" in the "Hitch Item Number" box, select "Draw-Tite" from the drop-down menu, and hit “Add to Cart” to place your order. This will get you all of the hardware from the hitch.

expert reply by: Kyle S

0

Answer 1

If you've broken or lost any of your hardware when installing your hitch all you need is to go to part #RHK, type your hitch item number in and select the manufacturer. This will give you a complete hardware kit to replace yours. You can buy a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

Hey Kirt, Congrats on the new car! To get your car safe to flat tow you'll need the following parts: Base-Plate #RM39FR Tow-Bar Adapter #RO64FR Lighting #RM-15267 Chargeline #RM-156-25 Air-Force One Vehicle Side #SM99209 and Hose #SM99666 (if you…

view full answer...

Answer 8

Hey, Bill. If you’re not installing a supplemental braking system, like part #DM86VR, then the answer is no, you won’t need to install a charge line kit (part #RM-156-25). You will, however, want to double-check your owner’s manual for the exact…

view full answer...

Answer 9

The Timbren Trailer Suspension Enhancement System part #TTRA1032 is my recommendation for a set of bump stops or jounce bumpers for a Dexter 7K Axle. These Timbrens will do a great job of compensating for off-center loads, reduces body roll when…

view full answer...

Answer 10

There is no specific torque rating for shackle bolts. You'll want to ensure that the bolts you use are long enough so that when installed you will have at least 2 threads protruding from the nut. Make sure that the bolt you're using has a…

view full answer...

Replacement Hardware for Draw-Tite Trailer Hitch 75758

Products Featured in This Question

Continue Researching