Gear Replacement for Bulldog Trailer Jack BD182404

Question

Question:

I am looking for a replacement gear for a trailer jack. Please see the attached pictures. Thanks!

asked by: Daniel Q

0

Expert Reply:

Could you get me the brand of the jack possibly?

expert reply by: Jameson C

0

Daniel Q.

9/3/2020

I am looking for a replacement gear for a trailer jack. Please see the attached pictures. Thanks!

Jameson C.

9/3/2020

If you have the Bulldog trailer jack part # BD182404 like you mentioned the correct gear replacement # BD500212.

Answer 1

Hey Bryant. The total lift measurement does include the drop leg. The Square Direct Weld Jack item #e42ZV you were looking at has a 28-3/4" total lift range that is measured by the 15" of screw travel, which is the actual jack itself, and…

view full answer...

Answer 2

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Answer 3

Hey Terry! It looks like there is a little delay on when it will be back in stock but the Dutton-Lainson Hand Winch #DL15440 is still around as far as I can tell. We don't have any notes on this winch being discontinued. The #DL14881 is available…

view full answer...

Answer 4

The length of your winch strap should be at least the winching distance required for loading the boat on the trailer. I would measure from the winch mount on your trailer back to the end of the bunks and go with a strap about that length. If that…

view full answer...

Answer 5

Hello Marcy, thanks for reaching out. We do have a good replacement option for you. Take a look at the Bulldog Square Jack #BD182804. This has a 27-3/8" retracted height and extends out to 39-1/2". It has a 10K lift capacity and 12K support…

view full answer...

Answer 6

The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return #BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity #BD1824200100. Your current…

view full answer...

Answer 7

A drill bit attachment like the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks #UF48-979005 is not available for the Square Direct Weld Jack #TJD-12000SP-F2 or #TJD-15000SP-F. This would only work on scissor jacks like the Leveling…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Gear Replacement for Bulldog Trailer Jack BD182404

Product Page this Question was Asked From

Continue Researching