Replacement Bearings for Dexter 8-256 Trailer Hub

Question

Question:

Hello. Im trying to replace the bearings on my trailer. 2 of the hubs are dexter 8-256.

asked by: Cory G

0

Expert Reply:

We have exactly what you need for a bearing kit for your Dexter 8-256 hub, with the correct bearing kit being the following:

- Bearing Kit # BK2-100.

This includes the bearings, races, and grease seal for your hubs. And for grease I recommend the Prime Guard Wheel Bearing Hi-Temp Red Grease # L11380, while for a bearing packer I recommend the Bearing Packer # PTW1218 or # ALL647646.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The Dexter "8-256" is a hub assembly that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in a few different bolt patterns therefore you would need to confirm your bolt pattern using the attached help…

view full answer...

Answer 2

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 10

Hey Scott! The correct bearing kit for your Dexter 6k axle is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you want the Dexter version it is the #DX26ER. What kind of trailer do you have?

view full answer...

Answer 11

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 12

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Replacement Bearings for Dexter 8-256 Trailer Hub

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching