Fan-Tastic Roof Vent Operator with Roller on Left Side of Arm

Question

Question:

Do you have this lift arm with the round knob on the end of the arm on the left side instead of the right? Like in the picture attached?

asked by: Attila D

0

Expert Reply:

We do have a Fan-Tastic lift arm with the roller on the side of the arm that you are looking for with the part # FVK8011-05.

expert reply by: Jameson C

0

Answer 1

Thank you for providing the pictures. The Fan-Tastic Vent Replacement Lift Arm for Roof Vents with Flat Lids item #FVK8014-05 replaces the flat roof vent arm on Fan-Tastic Vents. If you have a Domed shape Fan-Tastic vent you will need the Replacement…

view full answer...

Answer 2

I went out to our warehouse to take a couple measurements on the Fan-Tastic Vent Replacement Lift Arm #FVK8014-05 that you referenced. The distance between the two mounting holes, on center, is right at 3". The overall length on the arm is…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Fan-Tastic Roof Vent Operator with Roller on Left Side of Arm

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching