Recommended Suspension Enhancement for 2014 Toyota Sequoia Platinum

Question

Question:

Hey I have the 2014 Toyota Sequoia Platinum. It has three modes for factory rear suspension: Sport, Middle and Comfort. I am wondering do I need the Timbren SES for when I am towing or is the factory built-in air compressor going to do the leveling for me when I tow ie. 6500 lb trailer?

asked by: Normand

0

Expert Reply:

Your 2014 Toyota Sequoia Platinum does not require suspension enhancement if you are comfortable with the ride with your trailer connected in any of the 3 factory modes. The Timbren Rear Suspension Enhancement System # TTORSEQ1 are the correct fit if you want to add suspension enhancement which will take the brunt of the additional weight when towing to reduce wear on your factory suspension. These springs are designed to increase in rigidity and support as more weight is added working to provide stability and reduce body roll. They won't change the ride when you don't have a heavy load so adding them is my recommendation for you to pull a 6,500 lb trailer. I've attached a video that helps with a visual along with the explanation to assist.

expert reply by: Jason S

0

Answer 1

The description does mention an axle, but the principle is the same. Basically, right next to the rear coil springs on the 2011 Toyota Sequoia, there is a factory bump stop. You will remove the factory bump stop and install the Timbren system,…

view full answer...

Answer 2

Hey Matthew, yes the Timbren kit part #TTORSEQ1 that you referenced would work great on a vehicle that is lifted but you have to use spacers to take up that extra space created like with the part #T68MR. How big of a lift does your vehicle have?

view full answer...

Answer 3

Your 2008 Toyota Sequoia will not be raised at all when you install the Timbren system that fits, which is the following part number: - Timbren Rear Suspension Enhancement System #TTORSEQ1 When installed, the #TTORSEQ1 will have a gap between the…

view full answer...

Answer 4

Hi Jordan! The Dexter Bearing Kit for 1-1/16" to 1-3/8" Tapered Spindle #DX76ER uses bearings and seals that are made overseas. They aren't really "branded", per se, but Dexter does have them made specifically for them. If you…

view full answer...

Answer 5

The Timbren kit part #TTORSEQ1 that you referenced is the correct fit for your 2008 Toyota Sequoia and would give you additional suspension support when towing. That said I wouldn't necessarily recommend this kit unless you were planning to be…

view full answer...

Answer 6

From our experience the brake controller connector on a Toyota Sequoia is pretty tucked away. It's in a similar location as to the Tundra video you watched but harder to find. Take a look at the video I linked of the 2008 Sequoia, it's the…

view full answer...

Answer 7

The suspension of your 2008 Toyota Sequoia is soft enough that you'll experience some sag as you are towing the trailer you mentioned. Suspension enhancement like the Timbren kit part #TTORSEQ1 would be a really great idea to reduce this and give…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hi Donald, The Timbren Rear Suspension Enhancement part #TJRJK is a fit for a 2024 Jeep Wrangler Unlimited and installs by replacing your factory bump stops above your rear axle. Timbrens are easy to install and once they're on there isn't…

view full answer...

Recommended Suspension Enhancement for 2014 Toyota Sequoia Platinum

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching