How Far Out Does TorkLift GlowStep Stow N' Go Scissor Steps # TLA7844 Extend

Question

Question:

how far does this item extend out . i am trying to see if i can use this item for my boat. the boat lift to the dock is 29.5 inches. will this extend that far?

asked by: Jerry T

0

Expert Reply:

The TorkLift GlowStep Stow N' Go Scissor Steps # TLA7844 is going to extend out roughly 38 inches from where it installs. I say roughly since it's a scissor step and how far the steps extend changes the distance they stick out.

expert reply by: Jameson C

0

Answer 1

I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7843 away from your camper to clear your bumper. It may be possible to have a…

view full answer...

Answer 2

Not following the manufacturer's instructions to the letter will give them an excuse if something were to happen so while I can't recommend drilling the extra holes to ensure it's safely mounted, it's the only way that the steps will…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Hey Brady, Brophy in the past has told us that the tie downs part #HSWB don't have a weight capacity but you would want to make sure you use them only with campers that were designed to fit the bed length of the truck. The turnbuckles part #TDHP…

view full answer...

Answer 12

Hey John! You weren't finding that SolidStep because Lippert discontinued it in 2024 and that table wasn't updated to reflect this. What I recommend instead is the MORryde StepAbove RV Steps #MR26RR. These are designed to fit 23-3/4" to…

view full answer...

How Far Out Does TorkLift GlowStep Stow N' Go Scissor Steps # TLA7844 Extend

Product Page this Question was Asked From

Continue Researching