How To Measure for Round SnapPad Jack Stand Pads

Question

Question:

how do you measure? I measured and got 9 in front and 12inches in back. Thor Tuscany 40rt 2020

asked by: Steve

0

Expert Reply:

In regards to the SnapPad Jack Stand Pads, if you have round shaped feet then you would measure the diameter from end to end. If the feet measures 9" then you can use part # SP54FR2. I have attached a full list of options below but there are no options for 13" diameter feet.

expert reply by: Conner L

0

Answer 1

I have a solution for you, but the Ford Edge, Explorer and Taurus vehicles equipped with the 2.0-liter EcoBoost I-4 or 2.3L EcoBoost I-4 engine CANNOT be towed four wheels down. The 3.5L EcoBoost Engines do allow for flat towing. For the FWD versions…

view full answer...

Answer 2

The bottom portion of the SnapPad Jack Pads #SP54FR2 are approximately 1" thick but they are not meant to lift your wheels off the ground. If your wheels came off the ground that would mean you're putting the full weight of your RV onto the…

view full answer...

Answer 3

We should certainly have the correct SnapPads for your 2011 Thor Hurricane 31G. Unfortunately the is no online database we can reference that will tell us exactly what size pads you will need based off of the year make and model of RV. If you will…

view full answer...

Answer 4

Yes, the Replacement Rear Foot Pad for Lippert Ground Control 3.0 #LC377962 measure 9", meaning, the SnapPad Jack Pads for Class A and C Motorhomes w/ 9" Round Jack Feet #SP54FR2 will work great.

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

How To Measure for Round SnapPad Jack Stand Pads

Featured Help Information

Miscellaneous Media

Continue Researching