How to Remove Side Trim Panels on Jensen RV Stereo JWM60A

Question

Question:

How do you remove trim piece to access mounting holes

asked by: Mike T

0

Expert Reply:

The outer trim pieces on the Jensen RV Stereo # JWM60A (which is the same as your JWM62A model) are simply pressed into place and secured with the integrated tabs. To remove them you will just locate the small notch on the side of the trim (see attached picture) and use a flat head screwdriver to gently pry the panel away from the stereo.

Once the side panels are removed you will have access to the mounting hardware.

expert reply by: Chris R

0

click to enlarge

Answer 1

No, it is not Lori but that's typical. The Blu Technology Stainless Steel Water Hose w/ Quick Connects item #GB24FR has a stainless steel outer sheathing to protect the rubber inner tube that actually carries the water through the hose. The hose…

view full answer...

Answer 2

Either one of the CIPA #CM11550 or Longview #LVT-2300-C towing mirrors will work well for you. As you pointed out, the CIPA mirror will allow more of the mirror's turn signal to be visible. CIPA makes very high quality mirrors and even though we…

view full answer...

Answer 3

After looking up the wiring diagrams for your old RV Stereo AWM970 and your new Jensen RV Stereo #JWM60A (Jensen part number JWM62A) you new stereo should actually have 3 more wires, not less wires. The AWM970 had two connectors, a 12 pin and a 4 pin…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

How to Remove Side Trim Panels on Jensen RV Stereo JWM60A

Continue Researching