How to Lock Generator to Stromberg Carlson Bunk Platform Adapter

Question

Question:

How do you lock your generator to your trailer when using the Stromberg Carlson Trailer Tray?

asked by: Tony

0

Expert Reply:

Easiest way to lock a generator to the Stromberg Bunk carrier part # CC-255 would be to run a cable lock like the part # 8218DPS around the base of the bunk and then through the handles of the generator.

expert reply by: Jameson C

0

Answer 1

Yes, you can use a generator and leave it installed on the Stromberg Carlson Tray #CC-255. Just make sure you have the generator grounded properly, which is specific to which generator you have but will be listed in it's owner's manual.…

view full answer...

Answer 2

Since the Honda 2000-2200 watt generators have the pull start handles on the side rather than the top, it shouldn't be too difficult to start the generator once it's on the tray. Once installed, the cargo tray will sit about 29 inches above…

view full answer...

Answer 3

Yes, you can leave your generator mounted on the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 while you are using it! I would just be sure to mount the generator in such a way that the exhaust isn't pointing towards anything while in…

view full answer...

Answer 4

The first step in choosing a weight distribution system is to conclusively determine the tongue weight of your camper once it is fully loaded and ready to tow. This includes full water and propane tanks plus any other gear you would typically travel…

view full answer...

Answer 5

Hey Mike! Do you know how wide your frame is? I'm assuming wider than 68-11/16" since that is the mounting hole spacing on the Lippert system. The Trailer Valet Drill-Powered Stabilizer Jack #TV68FR has adjustable brackets but you're…

view full answer...

Answer 6

Hey Ray, thanks for reaching out. If you are set on placing the propane tank inside the toolbox, it can be done safely as long as the box is properly vented at the bottom. Propane is heavier than air, so if there is ever a small leak it will settle…

view full answer...

Answer 7

The Mount-n-Lock GennyGo Generator and Cargo Carrier MNT34FR is meant to be mounted on the bumper of your RV and cannot be mounted to the tongue of your trailer without some pretty extreme modification and fabrication. However there is still a…

view full answer...

Answer 8

For your toy hauler patio door I recommend using some drop leg stabilizer jacks like the Stallion Stabilizer Jacks #288-01892-2. These jacks have a retracted height of 15-1/4" and extended height of 22-1/4" and a combined weight capacity of…

view full answer...

Answer 9

No, the Stromberg Carlson Trailer Tray Cargo Carrier part #CC-255 would not interfere with the frame brackets on any of the Equal-i-zer Weight Distribution Systems. The reason for this is because of its wide range of adjustability. The Equal-i-zer…

view full answer...

Answer 10

I don't think you'd have any issue removing your propane covers with the #CC-255 installed. If you check out the pictures I attached you'll see this installed on a trailer that has the white version of your cover installed. In the last…

view full answer...

Answer 11

Thanks for the kind words. You are definitely correct that the Jack-It 2 Bike Rack for A-Frame Trailers - 22-1/2" Jack Clearance #LC429756 requires you to remove the tray in order to install it on your 2017 Casita A-frame travel trailer. If you…

view full answer...

Answer 12

To determine if a 2009 Chevrolet Silverado 1500 with a 5.3L V8 can tow your 2002 Coachmen travel trailer, you will need to find the towing capacity of the truck and weight of your trailer when it is loaded and ready to tow. I did some research on the…

view full answer...

How to Lock Generator to Stromberg Carlson Bunk Platform Adapter

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching