Axle Size Nut Retainer 6-190 Fits

Question

Question:

Replacement Nut Retainer for 6-191 Jam Nut Item # 6-190, will this fit a dexter 5200 axle?

asked by: Phil

0

Expert Reply:

The Replacement Nut Retainer for 6-191 Jam Nut # 6-190 fits Replacement Trailer Spindle Jam Nut # 6-191 which fits 2,000 lb to 8,000 lb axles with E-Z Lube spindles. That means it will fit your 5,200 lb axle if it has an E-Z Lube spindle.

expert reply by: Kyle S

0

Answer 1

I have attached for you the installation manual of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817. This is a generic install manual that can be used on any trailer but there is not a set of instructions specific…

view full answer...

Answer 2

Hey John, thanks for reaching out. So that #007-112-00 bolt is a 3/8" - 24 press-in bolt. We do have a longer 3/8"-24 bolt part #BRKH12S (1-1/4" long), but it isn't press-in. It comes with 4-bolts, nuts and lockwashers. That will…

view full answer...

Answer 3

I believe you are looking for the correct nut to fit the stud part #007-112-00 which would be the #38N.

view full answer...

Answer 4

It may be possible to change your studs from 1/2" to 9/16" so long as the studs are drive-in (as opposed to threaded); also, the length and knurl diameter needs to be the same. For example, the Kodiak Wheel Bolt - 9/16" Diameter x…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 7

Hey Justin, welcome back! The 136" measurement on the Parking Brake Kit #T2385201 is the overall length of the rear cable. It runs back roughly half that length on each side from where it runs through that central bracket. What kind of trailer…

view full answer...

Answer 8

Hey Brent, welcome back! For replacement brakes you need the Dexter Nev-R-Adjust Electric Trailer Brakes #23-468-469. You can also use our etrailer Electric Trailer Brakes #AKEBRK-35-SA if you want to save some money. For the hubs I'm assuming…

view full answer...

Answer 9

Hey Chase! Thanks for providing those measurements. The Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers #K71-359-00 is the right kit for your Jayco Octane. This matches your existing equalizer and shackles strap dimensions, and the wet…

view full answer...

Answer 10

Hey Al, Since your Dexter #9919860 is a 3,500lb axle you'll need grease seals #RG06-050 which come as a pair. I'd get 3 pairs (6 seals) that way you have an extra incase one goes in funky and bends (I've repacked hundreds of hubs and it…

view full answer...

Answer 11

The Dexter 8-283 is an obsolete 2800lb 10 x 1-1/2 inch hub that used a LM67048 inner and a L44649 outer bearing. Unfortunately, we don't have any hubs that would be compatible with the spindles on your axle. Your best bet at this point would be…

view full answer...

Answer 12

The Dexstar Conventional Steel Wheel part #AM20514 that you looked at is a great solution for your requirements. It will easily handle the 110 PSI your load range F tires require. The limiting factor is usually the valve stem. Using the Americana…

view full answer...

Axle Size Nut Retainer 6-190 Fits

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching