How to Test the Blue Wire on a Trailer Brake Controller on a 2004 Dodge Ram
Updated 09/13/2012 | Published 09/11/2012
Question:
How does the controller know that the trailer is their? how can I test the blue wire is all the way back? can a Volt meter add enough load to test this?, I might have a broken blue wire going back to the seven pin plug, just looking for an easy was to trouble shoot this I have a dodge 2004 , look like all the wiring is there?
asked by: Joe
Expert Reply:
A brake controller like the Prodigy, # 90885, will send a small amount of voltage back to see if a trailer is connected. The load from the magnets is what it is checking for. You can test the blue wire behind the controller and at the 7-Way with a meter.
To test the blue wire at the controller you will need to sever the wire a few inches from the back of the controller. Use your meter to test the end of the blue wire coming out of the controller. It should show voltage when you fully apply the manual override. If it does not you know that something is wrong inside the controller and it will need to be replaced.
To test to see if voltage is going all the way back to the 7-Way, have someone sit in the truck and apply the manual override while you test the pin in the 5:00 position. If no voltage makes to the back you know there is a break somewhere in the wiring (provided the blue wire goes all the way back).
On some Dodge Rams that came with a factory 4-Way connector, the blue brake wire does not go all the way back, it stops at the connector that is located under the drivers side wheel well. I have included a link to our brake controller installation troubleshooting FAQ.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Brake Controller
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: TruRyde Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Q&A: How to Determine What Brakes I Need for my Trailer?
- Q&A: How To Tell The Difference From Right and Left Electric Brake Assemblies
- Q&A: How to Choose the Right Brake Assemblies for my Trailer
- Q&A: How To Find Correct Replacement Electric Braking Assembly Parts for a Trailer
- Video: What to Know About the Curt TriFlex NEXT Trailer Brake Controller
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Custom Harness - 1 to 4 Axles - Proportional
- Q&A: Blue Wire Showing Voltage with No Trailer Connected and When Not Applying Brakes on Brake Controller
- Q&A: Testing a Vehicle Side 7-Way Trailer Connector for Proper Function
- Q&A: Should The Trailer Brake Circuit Have Continuity Between the Blue Power Wire and Ground?
- Shop: Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: How to Choose a Trailer Brake Controller
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer tires and wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: brake controller
- Article: How to Measure for Trailer Hitch Drop
- Shop: Gooseneck Hitch
on Trailer Brake Controller
