Wobble with the Hollywood Racks RV Rider 2 Bike Platform Rack for E-Bikes part # HLY64FR
Updated 07/14/2020 | Published 07/10/2020
Question:
Hello, I have installed the bike rack on the rear of my 5th wheel, as best I can determine based on the instructions. However I am getting a wobble that appears to be between the plastic sleeve and the tubing in the main pivot arm area.. The instructions seem to show the plastic sleeve in place but now I am wondering if perhaps it should not be there? What do you recommend? Thanks!
asked by: Rick N
Expert Reply:
The plastic peices are right where you want them. These will eliminate the play and noise we see in alot of the racks that do not have them. Your wobble is something I see a lot when bike racks like the Hollywood Racks RV Rider Bike Platform Rack for E-Bikes part # HLY64FR. It is a simple solution. Just tighten the main pivot bolt down a little bit more and retest until it get to the point you're looking for. This can be re done several times over the years to make sure it stays nice and tight.
Product Page this Question was Asked From
Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- RV and Camper Bike Racks
- Platform Rack
- RV Hitch Rack
- Frame Mount
- Bike and Hitch Lock
- 2 Bikes
- 5th Wheel
- Flat-Towed Vehicle
- Motorhome
- Fits 2 Inch Hitch
- Electric Bikes
- Fat Tire Bikes
- Heavy Bikes
- Hollywood Racks
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Hitch Anti-Rattle Devices: The Ultimate Guide
- Video: Curt Hitch Extender for 2" Hitch Receivers Review
- Video: An In-Depth Look at the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches
- Shop: Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Shop: Curt Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches
- Shop: Roadmaster Anti-Rattle Hitch Extender for Tow Bars - 2" Hitches - 7-3/4" Extension
- Shop: Thule Snug Tite Hitch Lock and Anti-Rattle Device
- Shop: Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span
- Shop: Gen-Y Anti-Rattle Clamp for 2-1/2" Hitch Receivers
- Shop: Curt Hitch Extender for 2" Hitch Receivers - 8" Long
- Shop: Trailer Hitch
- Video: Comprehensive Review: Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories
- Q&A: Is There A Hitch Extender For 2.5" Hitch With A 7,500lb GTW Capacity
- Q&A: Which Hitch Receiver Size is Better 1-1/4 inch or 2 Inch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Suspension Enhancement
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer jack
- Article: How to Choose the Right Trailer Hitch Class
- Video: How to Choose a Trailer Brake Controller
on Hitch Bike Racks
