Wiring Pigtail Needed to Install LumenX LED Trailer Backup Light

Question

Question:

I bought two of these backup lights for my fifth wheel. Cant find the plug that fits them anywhere including on your site or the Peterson site. The part is LumenX LED Trailer Backup Light - 7 Diodes - Clear Lens Part number PE37ZV Now what?

asked by: Pete P

1

Helpful Expert Reply:

To install your LumenX LED Trailer Backup Light # PE37ZV, you will want to use the Peterson 2-Wire Pigtail # PE23SR. This wiring harness is the AMP style that offers a weathertight connection. I confirmed this is the pigtail you will want to use with my contact at Peterson LumenX.

The white wire is for your ground and the red wire is for the reverse light signal for the light.

expert reply by: Victoria B

1

Answer 1

The easiest thing to use/install is the NightMinder RV Task Light #NM-Motion-011. This is a battery powered light that uses 3 AAA batteries (not included). All you need to do is get rechargeable batteries to avoid purchasing batteries constantly. It…

view full answer...

Answer 2

So the right way for you to do this will depend on how often you're going to use the lights and how many of them there are. If a trailer isn't equipped with a battery, the interior lighting is frequently tied into the running lamp circuit.…

view full answer...

Answer 3

In terms of brightness the part #ILL08COB is really hard to beat as it's going to be the brightest option we carry. We do have the part #ILL06COB which costs a bit less but is still relatively bright. About half as bright as the one you…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 11

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Answer 12

Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…

view full answer...

Wiring Pigtail Needed to Install LumenX LED Trailer Backup Light

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching