Could Custom Third Brake Light Camera kit part # 3460002 Fit 2017 Ford F-250

Question

Question:

I have a 2017 F-250 XLT with the smaller 4.2” I believe in dash backup camera. I was wondering if this product can be wired to the upfitter switches instead of the included toggle switch? Thanks,

asked by: John

0

Expert Reply:

The Custom Third Brake Light Camera kit part # 3460002 is a fit for your 2017 Ford F-250 that has the 4.2 inch screen size on the dash. We do not have a way to wire the switch to the switches you mentioned but I am sure there's a way it could be done.

expert reply by: Jameson C

0

Answer 1

The Third Brake Light Camera part #3460002 that you referenced is not available without a switch, this comes with a gasket which provides the seal but also silicone sealant/butyl tape is recommended, the factory screws of your truck are long enough…

view full answer...

Answer 2

The Custom Third Brake Light Camera #3460002 uses the supplied toggle switch as a power input to signal the module for switching to the optional 3rd brake light camera. To use one of the factory auxiliary switches on your 2021 Ford F-350 you will…

view full answer...

Answer 3

I do have third brake light options for your 2019 Ford F-250 although I am not exactly sure what you mean by interphase. The third brake light cameras available for the 2019 F-250 Super Duty are compatible with what specific monitor have from the…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…

view full answer...

Answer 6

Hey Mike, thanks for reaching out! The 16K Pullrite SuperGlide #PUL43RR is an excellent option for towing your Grand Design with your 2025 F-250, and if you lockout your Lippert Turning Point pin box you'll be able to use them together. You…

view full answer...

Answer 7

Yes, we do. What you are describing sounds like the Inner Frame Brackets for Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Hitch item #RP27FR. I have attached a picture below. These come welded to the frame exactly where you…

view full answer...

Answer 8

If you were to use the 4 inch offset ball #BWGNXA4085 the pin weight on the ball will not be changed. What will change is where the weight is carried on the truck. Using the offset ball will put more weight 4 inches back from the center of the…

view full answer...

Answer 9

Hello again Steve. According to Gen-Y, you want to go off the actual GVWR when selecting your pin box. Since your GVWR is 15,495 you will definitely want to go with the 2,500 lbs - 4,500 lbs pin weight capacity range. The Gen-Y Hitch Shock Absorbing…

view full answer...

Answer 10

Yes BedRugs like the #BRQ17SBK can be left in the bed of a truck when installing a slide in camper. The BedRug would not affect the fit of the camper and also would not get damaged.

view full answer...

Answer 11

Hey Flint, you did your homework and I appreciate it! Yes the Gen-Y cushioned pin box part #GY78GR is correct for your Forest River 330BH. It fits in place of your Rhino Box pin box and would be the pin weight range you'd need as well. What type…

view full answer...

Answer 12

Hey Jason, thanks for reaching out! We have a TorkLift tie-down kit for your 2022 Ford F-350 just as long as the electric running boards aren't wheel-to-wheel (I don't believe they are). The kit you referenced is for newer Super Duty pickups,…

view full answer...

Could Custom Third Brake Light Camera kit part # 3460002 Fit 2017 Ford F-250

Product Page this Question was Asked From

Continue Researching