Replacing Hubs, Bearings, Seals, and Races on a Trailer

Question

Question:

I bought a 5 x 4.5inch patter hub with 1-1/16inch bearing races but the hub was 4-1/4inch standing on end and the one i took off the trailer was 3-1/2 Will the DA54FR fit and do you sell one that is a kit with all the bearing and seals?

asked by: Mike

0

Expert Reply:

Yes the Dexter Axle UFP Idler Hub - 5 on 4-1/2" - E-Coated - 2,100-lbs Item # DA54FR is compatible with your axle. However, we do not have a hub kit available with the bearings and seals.

I recommend Replacement Trailer Hub Bearing - Item # L44649

and

Grease Seals (pair) Item # RG06-020

expert reply by: Shane H

0

Answer 1

Hey Bruce, it sounds like you might have some older seals, perhaps Transcom seals with the 1.983" OD. We do have one seal, the #10-9 seal, which has proven to be a suitable replacement for these seals. This is a double lip seal with a 1.5"…

view full answer...

Answer 2

If you wanted to replace you hub and while upgrading your wheels the #8-258-50UC1 would fit your axle since you said your bearings are L44649. This hub is compatible with 13 inch to 15 inch wheels so it would be a great option. This hub is also…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...