What is 4-Bolt Pattern that Trailer Brake Assembly part # AKEBRK-2 Is Designed to Fit

Question

Question:

Can you tell me the 4 post measurement on item Item # AKEBRK-2 I want to make sure that it the bracket I currently have will allow them to attach.

asked by: Derek

0

Expert Reply:

I attached a picture of a 4-bolt mounting flange like what the brake assembly part # AKEBRK-2 you referenced is designed to attach to. This is a standard dimension so I would be shocked if the flange on yours was different.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Electric Trailer Brake Kit - 7" - Left and Right Hand Assemblies #AKEBRK-2 is just the braking assemblies and will require you to purchase hub/drums separately. For this I recommend the Easy Grease Trailer Hub and Drum Assembly for 2K Axles…

view full answer...

Answer 2

The Electric Trailer Brake Kit - 7" - Left and Right Hand Assemblies - 2,000 lbs #AKEBRK-2 only includes the left and right hand brake assemblies. These are designed to fit 7" x 1-1/4" drums. If you need mounting hardware you would…

view full answer...

Answer 3

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

What is 4-Bolt Pattern that Trailer Brake Assembly part # AKEBRK-2 Is Designed to Fit

Product Page this Question was Asked From

Continue Researching