Taillight Replacement Lens for Trailer with Number SAE APC 04 DOT,

Question

Question:

I have a trailstar boat trailer tail light cover SAE APC 04 DOT, so does your A39R8 fit my trailer ? thank you Willy

asked by: Bill D

0

Expert Reply:

The SAE number is not normally a reliable way to find replacement lenses, but from previous customers who have had that same number and sent in pictures we were able to determine that the correct replacement lens is the # A39RB for the main lens and # A37RB for the side marker.

expert reply by: Jameson C

0

Dan N.

7/16/2025

I believe I have the identical trailer light covers as described in this link. https://www.etrailer.com/question-446250.html?srsltid=AfmBOorME4JR4rGy9elizQk01HCqcdepJ9UkQtwuHXX0xwBSV3xqq8AR The rear-facing light covers are fine, but the side light covers are both broken and read "SAE APC 04 DOT" in the center. In this link you mention a part number # A37RB for the side marker. However I don't see that part number on your website. Do you have the part or an acceptable substitute? Thank you very much! Dan

Jameson C.

7/16/2025

@DanN Would the part # A17RB work? That's a pretty similar side lens for a trailer taillight assembly.

Dan N.

7/16/2025

@JamesonC Thanks again. I went to Optronics website looking more closely at Bill D's remark above. I think he meant to type A39RB, not A39R8. According to Optronics website it says the A39RB is discontinued and customers are referred to the flatter A36RB which I would presume has the same length and width dimensions but without the inch-plus depth that the A39RB would have had. I might have solved my mystery! Thanks. Dan

Jameson C.

7/16/2025

@DanN Gotcha glad to help! Is your current taillight a red square for the main rear facing taillight lens? If so thats what the replacement lens part # A36RB is designed to fit.

See All (7) Replies to Dan N. ∨

Answer 1

The SAE STIAP2 04 DOT number you provided is a DOT approval number, which states that the lens is compliant with DOT regulations. Because of that, that number isn't typically a good identifier for finding a replacement lens. However, in this…

view full answer...

Answer 2

For LED tail lights for your 2017 Karavan boat trailer I recommend the LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger #TLL56RK. These lights are virtually identical to the lights that came with…

view full answer...

Answer 3

I don't have any reference to the "S2T216AP2 " that you provided but based on my research it sounds like you might have the Optronics LED Combination Trailer Tail Lights part #TLL160RK. If that is the case then the correct replacement…

view full answer...

Answer 4

The SAE number is not normally a reliable way to find replacement lenses, but from previous customers who have had that same number and sent in pictures we were able to determine that the correct replacement lens is the #A39RB for the main lens and…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Hey Kent! Your Alliance Avenue already has some great suspension components with the MORryde CRE3000 equalizers, wet bolt kit, and Rota-Flex pin box. I wouldn't replace any of those unless you're experiencing a specific problem. The next…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Taillight Replacement Lens for Trailer with Number SAE APC 04 DOT,

Continue Researching