Length of Kodiak K338GBZN Disc Brake Caliper Guide Bolt

Question

Question:

OVERALL LENGTH OF BOLT

asked by: MARK R

0

Expert Reply:

The Kodiak # K338GBZN disc brake caliper guide bolt is 3-5/8 inches long overall, minus the Allen head it measures 3-3/16 of an inch and the threaded portion is 7/8 of an inch. This is all shown in the photo I've generated for you.

expert reply by: Mike L

0

click to enlarge

Answer 1

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles #AKIHUB-545-35-G-EZ-K and the CE Smith Trailer Idler Hub Assembly w/ Case #CE13515 fit the same spindle, have the same bolt pattern, and are galvanized so yes, essentially the only things that…

view full answer...

Answer 2

The correct stainless steel guide bolt for your #T2HRCM10DAC is the Replacement Guide Bolt for Kodiak Calipers - Stainless Steel #KGBS.

view full answer...

Answer 3

While there is not a manual or video available for the Kodiak Disc Brake Caliper Rebuild Kit #KDBC225KIT I did find an expanded drawing of the parts of Kodiak Disc Brake Caliper #KDBC225S which should help so you can see how the pieces fit. The…

view full answer...

Answer 4

Hi Brett, are you referring to the guide bolts? We do carry some replacement guide bolts like the #KGBS which are brand and capacity specific. If they aren't Kodiak, Dexter, or DeeMaxx then we probably don't have a replacement part that fits.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Length of Kodiak K338GBZN Disc Brake Caliper Guide Bolt

Featured Help Information

Miscellaneous Media

Continue Researching