Can Adapter Plate be Used to Install Bulldog Velocity Series 12K Electric Landing Gear Jack

Question

Question:

have a 2015 Sundowner Horizon 6906 RS. what adapter plate is required?

asked by: Ron

0

Expert Reply:

According to the instructions for the Bulldog Velocity Series Electric Landing Gear Jack # BD185400 there are 2 ways to install this jack; you can either use at least four 1/2" grade 5 bolts, or four U-Bolts. There are no adapters to make this compatible with other styles of mounting so you'll need to check out the attached dimension photo and review video to help determine if this will work for your application or not.

expert reply by: Jon G

0

click to enlarge

Answer 1

I recommend using the Never Fail Bushings - 9/16" Inner Diameter, 11/16" Outer Diameter - 1-3/4" - Qty 14 #LC279685. For 1-3/4 inch springs you will want the Shackle Bolt with Locknut for Double-Eye Springs - 3" Long #166081.…

view full answer...

Answer 2

On your 2007 Pilgrim 40 foot 5th wheel trailer, I recommend using the Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs #UF17-943010. This landing gear will allow you to adjust independently for easy and quick leveling. The leg…

view full answer...

Answer 3

On the Bulldog jack #BD185400 the mounting holes require 1/2 inch hardware. I was able to determine that when fully retracted the overall height is 44.8 inches. It is about 33 inches to the top of the top bracket. The distance from the top of the top…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Can Adapter Plate be Used to Install Bulldog Velocity Series 12K Electric Landing Gear Jack

Featured Help Information

Miscellaneous Media

Continue Researching