Replacement for Dometic Manual Awning Arm

Question

Question:

have a Dometic awning and need non-power arm . mfg no. 8952002.400UL mfg/pnc. 958643597 serial. 60499546 sku. 9108853270

asked by: James R

0

Expert Reply:

The best option we have to replace an old Dometic awning arm is with the Solera Classic Universal Awning Support Arms part # LC434716 for 63"-68" or part # LC434718 for 68"-81". This is a universal kit that will allow you to keep your old fabric and roller all while upgrading to a new set of manual arms.

expert reply by: Conner L

0

Answer 1

Hello Carson, That is a rad camper. It looks like you just got it broke in. =) Thanks for emailing that picture over. It looks like you have either a Carefree Fiesta or Spirit awning. The good news is the Solera Classic Universal Arms for Manual…

view full answer...

Answer 2

While I was unable to confirm the exact dimensions of the Norcold 1200LRIM, I think your current refrigerator to be 63-1/4 inches tall, 32-11/16 inches wide, and 24 inches deep. Please confirm this. The Everchill RV refrigerator with freezer drawer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 9

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement for Dometic Manual Awning Arm

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching