How Does Happijac Camper Jack Attach to Camper

Question

Question:

How does this attach to the camper?

asked by: Alexander L

0

Expert Reply:

On the camper you'd have a set of the Happijac Z-brackets like part # LC182493 installed which is what the jacks like part # LC736514-4 attach to.

expert reply by: Jameson C

0

Answer 1

If you're looking for just the L-bracket for your HappiJac Electric Truck Camper Jack System #LC736514-ELKIT then you'll need part #LC182492. The flat bracket can be swapped out with part #LC182494 and the swing brackets can be replaced with…

view full answer...

Answer 2

Hey Brian. I have a solution but the hubs on your Sprinter are still going to be too close to the frame even if you switch to a different wheel and tire set up to use the Pacbrake item #PB36RV. These won't work with the way the rear end on your…

view full answer...

Answer 3

We do not carry the Reico-Titan products so my research was more limited but after doing some research I was able to locate the installation instructions for the Reico-Titan Jacks. They have brackets listed specifically for the "C" clamp…

view full answer...

Answer 4

Hey Vitaly, unfortunately the number on the lock core isn't the key number you are looking for. The only place it would be listed is on the key or if you were to remove the door latch it would be on the back of the assembly.

view full answer...

Answer 5

I reached out to Happijac who said yes, your 4200 can use the replacement clutchless motor head, which is the following part number: - Replacement Clutchless Motor Head for HappiJac Truck Camper Jacks #LC759927 They said this will work so long as…

view full answer...

Answer 6

Your truck camper jacks are more than likely obsolete due to the age of your 1998 Big Foot truck camper. So unless they have been updated already you will need a new set of jacks. You can replace them with a HappiJac Electric Truck Camper Jack System…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

How Does Happijac Camper Jack Attach to Camper

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching