What Size Channel Does the Curt Channel-Mount Coupler part # C25328 Fit

Question

Question:

I would like the dimensions of the but end of the following product need to see if this will fit existing sleeve: Curt Channel-Mount Coupler - Squeeze Latch - 2-5/16 Ball - 15,000 lbs

asked by: Curtis T

0

Expert Reply:

The Curt Channel-Mount Coupler - Squeeze Latch part # C25328 is designed to fit channel mounts that are three inches wide inside if the channel like the Curt 3-Position Adjustable Channel Bracket part # C48610.

If your current channel measure three inches wide inside the channel this is an excellent choice.

expert reply by: Randy B

0

Answer 1

The Curt Channel-Mount Coupler part #C25328 is designed to be used with an adjustable channel such as the Curt 3-Position Adjustable Channel Bracket part #C48610 which has an inside width of 3". Therefore, the width of the but end on the coupler…

view full answer...

Answer 2

In general yes, the channels that the channel mount coupler like part #C25328 attach to are all the same dimensions.

view full answer...

Answer 3

The bolts for channel mount coupler #CTA-280 have the markings for grade 8 bolts. They are 5/8 inch coarse threaded bolts so the minimum torque value is 159 and the max is 212 (foot pounds). Once torqued down the force will cause the metal of the…

view full answer...

Answer 4

The Grade 8 mounting bolts that come with the Trailer Coupler #CTA-280 have a 5/8" diameter and an overall length of 5-1/8" including the head. Without the head of the bolts they measured 4-13/16".

view full answer...

Answer 5

A little bit of play is acceptable, the coupler should be tight enough that the coupler won't come off the ball, but not so tight you can't close the latch. I typically tighten the coupler up until I feel a slight resistance when closing the…

view full answer...

Answer 6

The bolts for channel mount coupler #CTA-400 have the markings for grade 8 bolts. They are 5/8 inch coarse threaded bolts so the minimum torque value is 159 and the max is 212 (foot pounds). Once torqued down the force will cause the metal of the…

view full answer...

Answer 7

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

What Size Channel Does the Curt Channel-Mount Coupler part # C25328 Fit

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching