Gooseneck Coupler Lock for Kaufman Trailer

Question

Question:

I need a ball lock for my gooseneck Kaufman trailer what do u recommend

asked by: Sam

0

Expert Reply:

The correct lock for your Kaufman gooseneck trailer is the Blaylock EZ Lock Gooseneck Coupler Lock # BLTL-55-40D (which I confirmed with my contact at Kaufman). If you'd like a lock for the set screw as well then you can use the kit # BLTL-57-40D2 instead which includes both the lock for the coupler section and the set screw.

expert reply by: Jon G

0

Answer 1

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

Hey Bob, congrats on a setting up a new camper! Out of all of those options you'll also need to consider daily driving comfort unless that camper is a permanent addition to your truck bed. Listed below are a brief breakdown of each and a…

view full answer...

Answer 8

Hi Lance, I completely understand where you’re coming from on this. You can use your factory hitch with a 48 inch extension like part #TLE1648, so you don’t have to jump to the dual receiver setup right away since this extension is designed to work…

view full answer...

Answer 9

Hello Dennis, That is definitely something you will want to check with your setup. The B&W Continuum #BW78FR will sit about 9 inches below your trailer frame once installed, so you will want to measure from the ground to the bottom of the frame…

view full answer...

Answer 10

Hey Jack, yes the Torklift camper tie downs part #TL63PR are the correct set for your 2024 Ford F-350 Tremor with a short bed and factory hitch. The turnbuckles part #TLS9526-2 that you referenced as well would be a great set that matches what you…

view full answer...

Answer 11

Hi Clint, welcome back The HappiJac Original Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4 #LC182898 are likely what you are looking for and will be a good in between option (they are actually pretty nice and should last a good long…

view full answer...