Replacement Shroud for Coleman Mach 3 AC Model 7333-797

Question

Question:

I need to replace my shroud on my Coleman AC unit model 7333-797 can you help?

asked by: Brian M

0

Expert Reply:

The correct replacement shroud for your Coleman model number 7333-797 air conditioner is the MaxxAir TuffMaxx Replacement Shroud # MA00-325001.

This replacement is compatible with:

Mach 1 (7332 series) 890, A890, B890
Mach 1 (8332 series)
Mach 3 (7333 series),A697, B697, *797*, A797, B797, A860, B860, C860, 880, A880, B880, C880, 890, A897, B897
Mach 3 (8333 series)

expert reply by: Carla M

0

Answer 1

The brown (running light) wires all run to each other as they carry the same circuit. The reason there is two browns on the trailer side is because there are running lights that are on both sides of the trailer. Aside from that all the rest of the…

view full answer...

Answer 2

When testing the brown wire on your trailer, all of the tail lights on the trailer should be activated. Since you are using a standard 4-wire harness on the trailer, you will need to make sure that you are using jumper wires to provide running light…

view full answer...

Answer 3

In order to wire your pop-up trailer with a 4-pole wiring harness like the 35 Ft 4-Way Trailer Wiring Harness - Wishbone Style #A35W42B, you're going to first have to: 1. Connect the white ground wire to your trailer's frame. You'll want…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hello Tom, Thanks for writing in. You are correct. I would not recommend using the B&W Digital Tongue Weight Scale #BW34KR with a McHitch coupler. The McHitch uses a different coupling design than a standard ball coupler, and I cannot confirm…

view full answer...

Replacement Shroud for Coleman Mach 3 AC Model 7333-797

Featured Help Information

Miscellaneous Media

Continue Researching