Replacement Stabilizer Switch for Lippert 113407

Question

Question:

I have a Lippert model#113407 stabilizer switch to replace. My TT is a 2014 Forest River V-lite 30WTBSK. Can you confirm this part is there correct replacement part?

asked by: Lou M

0

Expert Reply:

You might be able to use the RV Landing Gear Switch # 37213635, but when I reached out to my contact at Lippert he said that their exact replacement for your Lippert 113407 is the Replacement White Power Switch # LC144214 so I recommend going with the exact replacement from Lippert just to be on the safe side of things.

expert reply by: Jon G

0

click to enlarge

Answer 1

I checked with the manufacturer, SnapPad, and verified the XTRA pads you asked about do fit 5-3/4" jack feet; so you can use the following: - SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 6" Square Jack Feet #SN99FR The SnapPad…

view full answer...

Answer 2

Yes, I have attached the wiring diagram of the Replacement Electric Jack Switch with Harness #LC387874 for you to reference. Basically the Blue wire goes to a 6A auto reset breaker, like part #LC134181, which then goes to the positive circuit for…

view full answer...

Answer 3

The Lippert stabilizer jacks like you have use an 6 amp auto reset circuit breaker and a 20 amp fuse or breaker. If you check out the diagram I attached you'll see how it normally would be wired. For a 20 amp breaker you'd need the part…

view full answer...

Answer 4

To replace the Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD you'll just need to keep track of how the original was hooked up and replicate that. Unfortunately Lippert doesn't have a wiring diagram but we do have a photo we…

view full answer...

Answer 5

I've drawn up some dimensional drawings for you below for the Replacement Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Replacement Stabilizer Switch for Lippert 113407

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching