Is It Possible this will fit on Another Manufacturers Awning ?

Question

Question:

Hi, Could you please help to confirm the #8880736 Replacement Mounting Bracket fit on other brand awning ?

asked by: EasonL

0

Expert Reply:

The Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning part # 8880736 is designed specifically for the Yakima SlimShady roll-out awning part # Y36VR. If you have the manufacturer and model information off of your awning I can help to find the part you need.

expert reply by: Randy B

0

Answer 1

In regards to the Replacement Clamp Assembly for Yakima SlimShady Roll-Out Awning part #8880737, the handle on the side of the unit is used to tighten the c-shaped clamps around the crossbar. The rubber inserts inside the c-shaped clamps are then…

view full answer...

Answer 2

Since we don't sell ARB products, I'm unable to tell you with any certainty whether or not you can make this work; Yakima also doesn't test their products with other manufacturers. If you're trying to use the T-slot mounting channel…

view full answer...

Answer 3

While there isn't a mosquito net for the Yakima SlimShady part #Y36VR that you referenced the very similar Thule Tepui Tent part #TH8002AW604 does have one available with the part #TH8002X1001. The Tepui is a similar size roof rack mounted tent…

view full answer...

Answer 4

We have a roof rack awning that does fit the factory crossbars of your 2019 Toyota RAV4 as the Yakima SlimShady part #Y36VR but the Rhino Rack Batwing you mentioned requires a roof rack that has top channels so you'd have to add that as well. You…

view full answer...

Answer 5

Yes, you can use the Replacement Clamp Assembly #8880737 and Replacement Mounting Bracket #8880736 for the Yakima SlimShady will work for your Roam awning. We actually have a review from a customer who purchased this combination for the same exact…

view full answer...

Answer 6

Isaiah, the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning #8880736 measures 4" center to center on the bolt holes, and has a 1 1/2" vertical spacing.

view full answer...

Answer 7

Hi Tim; based on what we have found in the past the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning #8880736 will fit your Roam Adventure awning. The mounting bracket will connect to the Replacement Clamp Assembly for Yakima…

view full answer...

Answer 8

Great questions. Yakima SlimShady Awning - Roof Rack Mount - Clamp On - 8' Long x 8' Wide #Y96VR. Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning #8880736. Replacement Clamp Assembly for Yakima SlimShady Roll-Out Awning…

view full answer...

Answer 9

The vertical spacing you're asking for is 1-1/2" for the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning #8880736 (see attached). I confirmed this with my contact at Yakima.

view full answer...

Answer 10

I may have a solution for you, but since we don't sell CVT awnings there's no way for me to test whether you'll be able to get the awning connected to your Yakima HD bars. I'll also say that the Yakima Replacement Clamps #8880737…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Is It Possible this will fit on Another Manufacturers Awning ?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching