Which Roadmaster Rear Sway Bar Fits 2005 GMC Sierra 2500HD 4x4

Question

Question:

Is this the correct rear sway for 2005 Sierra 2500HD 4x4 Do the bolts for the arms go through the bed?

asked by: David

0

Expert Reply:

Yes, the Roadmaster sway bar part # RM-1109-167 that you referenced is the correct fit for your 2005 GMC Sierra 2500HD. None of the components of this kit end up going through the truck bed also.

expert reply by: Jameson C

0

Answer 1

Instead of using a tongue extender for your trailer you could use a hitch extender like the part #C45791 to basically get the same effect. This is an 8 inch extender that would work well for you. You should note that using an adapter like this will…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

Hey William, thank you so much for all of the information! To replace your axles, I recommend the Trailer Axle w/ Electric Brakes item #e73SR. This is a 6,000 lbs axle that come ready to install with pre-greased hubs and electric brake assemblies.…

view full answer...

Answer 8

Hey Frank, thanks for reaching out! What Dexter Axle means by this is that you want the grease zerk fitting from the wet bolts in the Dexter E-Z Flex Suspension Kit #K71-653-00 to face the outside of the trailer, rather than under the trailer. I see…

view full answer...

Answer 9

It sounds like you are looking for a u bolt kit for a 3,500 lbs axle. The 3-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 25-1/4" Long item #e57SR will work great for a tandem axle suspension system. For your ubolt kit you're going to…

view full answer...

Answer 10

Thank you for providing that information. Leaf springs like the ones you have now typically match the axle capacity on your trailer. Although adding leaf springs with a slightly higher capacity won't hurt, it also is not necessary. Based on the…

view full answer...

Answer 11

Hi Austin, I can help you determine the right replacement double-eye leaf springs for your 2018 Jayco trailer, though we don't have any way of knowing what specific ones you need. It's pretty easy though, as all you need to do is measure your…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Which Roadmaster Rear Sway Bar Fits 2005 GMC Sierra 2500HD 4x4

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching