Is There RV Roof Vent Option with Wall Mount Controller

Question

Question:

Is there one with a wall mount? I dont want a remote

asked by: Tom

0

Expert Reply:

I have a solution that I think would work well for you but all of the roof vents we offer for RVs do use either remotes or controllers on the assembly itself. The MaxxFan Plus Roof Vent # MA00-04500K though comes with a wall mount for the remote though so you could leave the remote in the wall mount and you'd basically have a wall mount controller.

If you check out the picture I attached you can see the remote being held in the wall mount.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX is meant to be a direct replacement however not all the necessary hardware is included. The remaining items you'll need is the Key Wall Control part #MA00A03550K,…

view full answer...

Answer 2

Hey Devon, does your RV roof vent wall control unit look like the #MA59FR? If so you have a MaxxFan Plus RV roof vent that was designed for wall control and for a replacement unit you would want the part #MA00-04500K to use a setup that would use…

view full answer...

Answer 3

You reported that you cannot use the remote on your MaxxFan 4700K to put the vent cover up and down. Let's troubleshoot. Put some new batteries in your remote. Ensure that the display comes on. Verify if your vent cover now works. Verify if other…

view full answer...

Answer 4

Hey Paul, yes we do. You can use the Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX to replace your current fan and will work with your original controller and garnish.

view full answer...

Answer 5

The MaxxAir roof vent part #MA00-04751KSX can be used with the Replacement Key Wall Control For MaxxFan Plus and Deluxe #MA00A03550K which is wireless.

view full answer...

Answer 6

Unfortunately the Atwood 85736 cannot be replaced so you'd actually need an entirely new actuator. The closest replacement we have is the Demco Hydraulic Brake Actuator #DM72VR. This actuator has a gross towing weight capacity of 7,000-lbs, a…

view full answer...

Answer 7

I don't have a wiring diagram, but I'd be happy to explain it for you. In order for the reverse solenoid on a Hydraulic Brake Coupler like #DM62VR to function, one of the two wires leading from it needs to be connected to the wire from the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is There RV Roof Vent Option with Wall Mount Controller

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching