Can Top Bracket for Lippert Bolt-On Shock Kit Be Cut to Ensure 45 Degree Angle on Shocks
Updated 02/03/2020 | Published 02/01/2020
Question:
Is it acceptable to cut the top bracket to ensure that the shock is not more than 45 degrees.
asked by: Louie C
Expert Reply:
I reached out to my contact at Lippert regarding the Bolt-On Shock Kit # LC281281 that you referenced. He said that the top bracket could be trimmed just a bit if needed to ensure a 45 degree angle on the shock, but it really depends on how much you are needing to cut. He said if you just need to file down a corner or something minimal like that it's not an issue.
However, if you are needing to cut off a more substantial section of the bracket or actually take off a piece that would eliminate one of its bolt holes, then it wouldn't be recommended. Doing this may affect the bracket's integrity and lead to failure down the line.
If you can tell me a bit more about what kind of cutting needs to be done I will be happy to help further. In the meantime I have attached the full installation manual below that you can look through.
Product Page this Question was Asked From
Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 5,200-lb to 7,000-lb (3") Overslung Axle
- Trailer Suspension Parts
- Leaf Spring Enhancement System
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Round Axle - 3 Inch
- Single Axle
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: How to Adjust Height on Curt Q24 5th Wheel Hitch for Ram Factory Prep Package
- Q&A: Road Armor Equalizer that Could Fit 2022 Keystone Passport 282QB
- Q&A: How to Measure to Determine Fit of Lippert Bolt-On Shock Kit LC281281
- Q&A: Troubleshooting Trailer Tire Wear on the Outside Edge of the Tire
- Q&A: Which Way Should Shocks of Lippert Shock Kit # LC281281 Face Relative to Axle
- Q&A: Upgrading Trailer Tires to a Higher Load Rating Radial Type for Extra Safety Margin
- Search Results: trailer shock kit
- Search Results: pin box
- Shop: Dexter Bronze Bushings - Qty 4
- Shop: MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert 1621 and 1621HD
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers w Correct Track - 2-1/4" Shackle Straps
- Shop: Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 5,200-lb to 7,000-lb (3") Overslung Axle
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Shop: Brake Controller
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: trailer jack
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
on Trailer Suspension Parts
