Lift Kits that Fits 2018 Geo Pro 19FBS with Dexter #10 Torflex Axle

Question

Question:

Which lift kits will fit this set up? Thanks! Lift kits for 2018 Geo Pro 19FBS with Dexter #10 axle

asked by: Brian V

0

Expert Reply:

Since your 2018 Geo Pro 19FBS has a Number #10 Dexter Torflex axle the correct lift kit you need is the part # K71-707-01. This will give you a lift of 2-5/8 inches.

I attached a review video for this kit for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Hey George, thanks for reaching out! According to my research you need the Global Link Ultra E Pro Travel Trailer Lock #295-000183. This fits a 3-3/4" tall x 2-3/4" wide cutout so you'll need to verify that's what you have on your…

view full answer...

Answer 2

I currently do not have an installation video of the Axle Riser Kit for Single Diamond Torsion Axle part #LC270682. I have linked a photo for you showing it after it has been installed installed on a different camper. As you can see it is extremely…

view full answer...

Answer 3

I have an option for you, but there is not a Lippert lift kit specifically for tandem axles. Instead you would just use two of the axle riser kits (1 for each axle): - Axle Riser Kit - Single Square Torsion Axle #LC382741 (works with Lippert 3,500…

view full answer...

Answer 4

I've attached the installation instructions for the Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch - Remote - 2,000 Watts - 12V #PD64FR for you below.

view full answer...

Answer 5

While we don't have your exact axle in stock we have a great solution with the Timbren Axle Less kit part #ASR5200S01 as a great solution that's available now. This is a 5,200 lb axle setup that's similar to the torsion setups but…

view full answer...

Answer 6

Adding solar panels and building a battery bank for off-grid camping camping is great, we can definitely help with most of the items needed for this. If your Geo Pro already has a fixed 190W panel mounted to the roof running through a 30 amp charge…

view full answer...

Answer 7

I do have an option to get you more lift but the Lippert Axle Riser Kit part #LC382741 will not work on a Dexter Torflex Axle so you will need to use the Dexter Axle Riser Kit part #K71-707-02 if this is the route that you choose. The torsion axle…

view full answer...

Answer 8

The Forest River Rockwood GEO Pro Trailers have Dexter Torflex Axles so we do have lift kits available. However, there are different lift kits depending on which particular Dexter Torflex Axle you have and I don't have this information.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Lift Kits that Fits 2018 Geo Pro 19FBS with Dexter #10 Torflex Axle

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching