Wheel Cylinder Assemblies for 7 Dexter Brakes

Question

Question:

I would like to purchase Wheel Cylinder Assembly - RH Item # 54-80-4 and the left hand LH for 7 x 1-3/4 Inch Drums . Do you have them? If yes, what is the price for both?

asked by: Bob Z

0

Expert Reply:

The matching wheel cylinder for 7" brakes that pairs with the # 54-80-4 is the Wheel Cylinder Assembly Kit -LH # DA24FR. These are both of the parts you need to change both of the wheel cylinder assemblies on your 7" Dexter brakes. These cylinders will fit 7" brakes like the # 23-398-399.

expert reply by: Erik B

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 4

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 5

No, it will not Bryan. The Redarc Tow-Pro Link item #RED57AR requires a USCAR port that comes with factory tow packages. The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit item #SH25VR, that fits your 2023 BMW X5, does not have this…

view full answer...

Answer 6

I do have an option for you although we don't have a set of hubs which use the LM11948 bearing. Therefore, the only option we can offer is a new axle which allows you to upgrade to a standard hub/drum and braking assembly. In order to choose the…

view full answer...

Answer 7

Hi Greg, Based on what you’re describing, if you cracked the brake line and got no fluid when the brakes were applied, that points more toward that the system isn’t building or sending pressure at all. In a surge setup with a lockout solenoid, fluid…

view full answer...

Answer 8

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 9

Hello Greg, Yes, you can use the same drum for the electric brakes that you used with your hydraulic brakes. Based on the measurements you provided, it looks like you have a #84 spindle, which typically means you're working with a 3,500 lb axle.…

view full answer...

Answer 10

Brakes like the Dexter #23-398-399 that are rated for 2,500 lbs have the capacity to work with 1,800 lb axles, but to get the right brakes you'll need to know your brake's mounting flange bolt pattern as well as your drum diameter. The…

view full answer...

Answer 11

Hey John, to pick out the correct brake assemblies for your Jayco 1406 I would need to know the axle capacity if you can get that to me. Then for a drum brake surge actuator the Demco part #DM72VR would be what you'd need to replace the Atwood.…

view full answer...

Wheel Cylinder Assemblies for 7 Dexter Brakes

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching