Torque Specs for etrailer Electric Trailer Brake Kit AKEBRK-35-SA
Published 12/18/2019
Products Featured in This Question
Question:
Hi, I received my brake replacement assemblies kit AKEBRK-35-SA, but no instructions were included. Can you tell me: - recommended torque for mounting bolts? - initial adjustment procedure? Thanks
asked by: Chris D
Helpful Expert Reply:
The brake mounting hardware for the # AKEBRK-35-SA, which can be obtained with part # BIK-00, should be torqued between 45-70lbs during installation; if you don't have a torque wrench you'll want to tighten the bolts until the lock washer is flat against the backing plate.
In order to do the initial, manual adjustment on the # AKEBRK-35-SA you will use the star style adjustment wheel at the bottom of the assembly; this process is briefly shown around the 2:00 mark in the installation and review video that I've linked to this answer.
Product Page this Question was Asked From
etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 13 Inch Wheel
- 14 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: 3500 lb axle
- Search Results: leaf springs
- Video: etrailer Self-Adjusting Electric Trailer Brakes Install Guide - 2017 Starcraft Travel Star Fifth Whe
- Shop: Trailer Axle Beam with Easy Grease Spindles - 4" Drop - 89" Long - 3,500 lbs
- Shop: CE Smith U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts - Zinc
- Shop: 6-Leaf Slipper Spring w/ Hook End for 8,000-lb Trailer Axles - 29-1/2" Long
- Q&A: Does etrailer Trailer Axle Beam e53GR Use L68149 and L44649 Bearing Combination?
- Article: Trailer Wiring Diagrams
- Q&A: Torque For etrailer 12 Inch Electric Brakes
- Shop: Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Shop: 3-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 23-1/8" Long
- Q&A: What Info is Needed to Install Drop Axle on Trailer
- Q&A: What is the Best Grease for Trailer Bearings
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Search Results: trailer wiring
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Video: How to Choose a Trailer Brake Controller
- Search Results: trailer jack
on Trailer Brakes
