Does Center Point Air Ride Trailer Suspension System Fit with MorRyde X Factory Crossmemeber

Question

Question:

I have a MORyde X Factor Cross member on my trailer. Will this interfere the Center Point Air Ride?

asked by: Jay

1

Helpful Expert Reply:

The Lippert Center Point system part # LC1565391 would work just fine with the Mor/Ryde X Factor Crossmember setup you have on your trailer but you would need to remove the center X-Factor.

expert reply by: Jameson C

1

Chris H.

4/18/2026

Hi there, I installed the Lippert Centre point air ride from you guys on my fifth-wheel tandem axle, but I want to add the MORryde X-Factor Crossmember. Surely this will interfere with the airbags, or do you place them front and back of the two-leaf spring hangers? thaank Chris

Jameson C.

4/20/2026

@ChrisH You are correct the X-Factor would only work on the front and rear hanger and would not work on the center hanger. I should have been more specific.

Answer 1

There are leaf springs available with measurements close to 25" from center of spring eye to center of spring eye, though the correct one is going to depend on your axle capacity, which should be stamped onto the axle itself. Knowing this…

view full answer...

Answer 2

There is no specific torque rating for shackle bolts. You'll want to ensure that the bolts you use are long enough so that when installed you will have at least 2 threads protruding from the nut. Make sure that the bolt you're using has a…

view full answer...

Answer 3

Hey Brian, yes the Furrion Chill Cube RV Air Conditioner w Air Distribution Box #FR99TD is compatible with your Dometic setup. I'd actually go with the Furrion Chill HE Replacement RV Air Conditioner for Coleman Setup #FR42PV though because this…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

Hey Neil. The 18,000 Btu Furrion Chill Cube RV Air Conditioner item #LC34DX fits a 14-1/4" x 14-1/4" cutout which is pretty standard on RV's. If you meant to write Dometic instead of domestic then yes it'll fit in your existing…

view full answer...

Does Center Point Air Ride Trailer Suspension System Fit with MorRyde X Factory Crossmemeber

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching