What Hitch Pin Diameter Does B&W Tow & Stow 2-Ball Mount # BWTS30040B Use

Question

Question:

what size diameter pin does this require?

asked by: Vince

0

Expert Reply:

3 inch hitches like what the B&W Tow & Stow 2-Ball Mount # BWTS30040B was designed for use the same hitch pin diameter as the smaller 2 inch and 2.5 inch hitch size which is 5/8 inch diameter.

For a locking hitch pin to use with this we have the Weigh Safe part # WS05 which would work great. I attached review videos for the hitch lock and the ball mount for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Rock Tamers Heavy Duty Mud Flaps are a great addition to a truck or RV. This will protect your vehicle and the towed items from stray rocks, debris, and water backsplash. For a 2" receiver go with Rock Tamers #ERT00108, for 2-1/2"…

view full answer...

Answer 2

In order to determine how much drop you need, you will measure from the top inside edge of your trailer hitch receiver on your 2017 Ford F-250 to the ground. Then you will measure from the ground to the bottom of your trailer coupler when it is…

view full answer...

Answer 3

Personally I prefer the Demco Trailer Coupler #DM14976-52 with the composite handle over the Coupler #DM15791-81 with a metal handle. I feel it is easier to operate as it does not have the safety latch like you get on the metal handle. Since most…

view full answer...

Answer 4

I went out to our warehouse to take a look at the B&W Tow & Stow 3-Ball Mount #BWTS20048B and measured a distance of right at 5-1/2 inches from the bottom of the shank to the lowest point of the vertical adjustment post. I have attached an…

view full answer...

Answer 5

I went out to our warehouse to take a look at the B&W Tow & Stow 3-Ball Mount #BWTS20049B referenced in your question. I measured a total length of right at 11 inches of the vertical adjustment shank on the ball mount. I have attached a short…

view full answer...

Answer 6

In regards to the B&W Tow & Stow 3-Ball Mount part #BWTS10048B for 5" or part #BWTS10049B for 7", the distance from the top of the shank to the bottom of the upright while the hitch balls are stowed away is 8.5" for the 5"…

view full answer...

Answer 7

Hey Michael, the correct lock kit for the B and W Tow N Stow #BWTS20040B is the part #34061775-D although it does say it's for the lighter duty kits. The shear strength of this kit is 42,000 lbs so you won't have anything to worry about.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

What Hitch Pin Diameter Does B&W Tow & Stow 2-Ball Mount # BWTS30040B Use

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching