How To Turn On Heat of 12-Volt Heater and Defroster # PTW5009

Question

Question:

But still wont let u use heat and fan same time

asked by: Tina

0

Expert Reply:

There's a rocker switch on the side of the 12-Volt Heater and Defroster # PTW5009 that you referenced that allows you to pick heat or fan. If you rock the switch towards the word "heat" it will put out heat and defrost your windshield.

expert reply by: Jameson C

0

click to enlarge

Tina

10/29/2019

But still wont let u use heat and fan same time

Jameson C.

10/29/2019

The fan of the # PTW5009 is designed to run in the heat and fan position. In both settings the same fan speed should be running. If your fan isn't running in the heat mode that would indicate it has a problem.

Answer 1

Hey Mark, the distance between the mounting holes of the JR Products Magnetic Baggage Door Catch #JR64ZR is 4 inches.

view full answer...

Answer 2

Heater #PTW5009 draws 13 amps at 12 volts which equals out to about 156 watts. I did a little research and from what I could find it is not ceramic.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

How To Turn On Heat of 12-Volt Heater and Defroster # PTW5009

Product Page this Question was Asked From

Continue Researching