Dimensions of Plate that Holds Ball of Curt Friction Sway Control part # 17200

Question

Question:

Looks like the trailer ball plate is 3inch x 3inch the one that is mounted on the trailer frame - can you confirm?

asked by: Jeff B

1

Helpful Expert Reply:

Yes, the ball plate of the Curt friction sway control part # 17200 that you referenced is 3 inches long by 3 inches wide.

expert reply by: Jameson C

1

Answer 1

Welcome back William! You are getting pretty close to the max capacity of your current set up, so swapping the bars to the Replacement Trunnion Spring Bar for Fastway e2 Weight Distribution Systems - 600 lbs TW #FA92-02-0699 will definitely help you…

view full answer...

Answer 2

Hi Jim; that does indicate it is for the 800/8,000 lb system. They do make a lower rated trunnion #FA92-02-0644 but you don't have to replace yours with the lower rated component. You can swap out your spring bars for the #FA92-02-0699. Are you…

view full answer...

Answer 3

I recommend using the Fastway e2 Weight Distribution #FA92-00-0800 for your 7x14 Interstate Loadrunner tandem axle trailer. This hitch is rated for trailers up to 8,000lbs with a tongue weight between 400-800lbs. If your unloaded tongue weight is…

view full answer...

Answer 4

The weight of the Trunnion Spring Bar #FA92-02-0699(13lbs) does need to be considered for the over weight of the trailer and maximum payload but is not used in the calculation of the tongue weight rating for the Fastway e2 Weight Distribution…

view full answer...

Answer 5

Yes, the Replacement Trunnion Spring Bar for Fastway e2 Weight Distribution Systems part #FA92-02-0699 which are rated for 600 lbs will work with the Fastway e2 Weight Distribution System part #FA92-00-0450 which is rated for 450 lbs.

view full answer...

Answer 6

Yes, if the Fastway e2 Weight Distribution System you have now has trunnion spring bars like part #FA92-00-0800 then you can use the Replacement Trunnion Spring Bars part #FA92-01-0699.

view full answer...

Answer 7

To move to a different spring bar weight capacity/range you have to just replace the bars if it's a round bar setup or the bars and the head of the system if it's a trunnion setup. So if you have a round bar setup now you'd want two of…

view full answer...

Answer 8

Your Trunnion Fastway e2 Weight Distribution #FA92-00-0600 is capable of using 6,000lb to 12,000lb bars. 6,000lb Replacement Trunnion Spring Bars #FA92-01-0699, 250-600lbs of tongue weight 8,000lb Replacement Trunnion Spring Bars #FA92-01-0899,…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Dimensions of Plate that Holds Ball of Curt Friction Sway Control part # 17200

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching