How To Install The Lippert Components Power Stabilizer Trailer Jack

Question

Question:

Does the black ground/negative wire have to be returned to the battery or can it be grounded to the rv frame.

asked by: Olwen H

0

Expert Reply:

The black ground wire from the The Lippert Components Power Stabilizer Trailer Jack # LC298707 needs to be grounded to the negative side of the battery not the trailer frame. The red wire needs to be connected to the positive side of the battery via a 20 amp breaker. I have attached wiring diagrams that will help you with installation.

expert reply by: Heather A

0

click to enlarge

Answer 1

Determining between piano hinges, #H300 3 Inch Wide Steel 6 Ft Long or #SH200 2 Inch Wide Stainless Steel Hinge 6 Ft Long, depends what features you find more important for your application. The #H300 hinge will be stronger in that it is an inch…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 5

Hey Tom, great question! Both products provide an easy way to measure tongue weight, but they excel in different situations. The BTBRV Trailer Jack Foot Scale #BTBRV014 measures tongue weight at the trailer jack, so you don't need to position a…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Heidi. To use a Curt Echo Wireless Brake Controller item #C51180 on a tow vehicle with only a 4-way connector, you'll need the 7-Way RV Upgrade Kit for Trailer Brake Controller Installation item #ETBC7L. The Curt Echo item #C51180 requires a…

view full answer...

Answer 8

The factory brake controller connector on your 2021 Jeep Grand Cherokee is located under the dash behind the hood latch, as shown in the provided photo. Keep in mind, the connector will only be there if the vehicle has the factory tow package which…

view full answer...

Answer 9

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 10

There are no differences between the Demco Tabless Base Plate Kit part #DM9519291 and etrailer Invisible Base Plate Kit part #e98950, this is just who we use for our braded base plates. I recommend whichever is more cost effective at the time. They…

view full answer...

Answer 11

Yes, you can flat tow a 2020 Jeep Grand Cherokee Limited, so long as it is 4-wheel drive and with "4-LO Range" according to the owner's manual. If you get this version, here are the parts I recommend in order to flat tow the Grand…

view full answer...

Answer 12

Hey Rob, for your 2021 Jeep Grand Cherokee I would recommend the Prodigy P3 part #TK28ER which comes with a custom fit harness designed for your Grand Cherokee. The P3 is the nicest controller around due to how easy it is to use and setup and how…

view full answer...

How To Install The Lippert Components Power Stabilizer Trailer Jack

Featured Help Information

Miscellaneous Media

Continue Researching