Replacement Pins and Balls for a Convert-A-Ball Interchangeable Ball Set

Question

Question:

can i buy just the pins that hold the ball in place i lost the 2inch and 2 5/16 pins

asked by: Steven

0

Expert Reply:

The internal pins in the balls are not available separately but you can replace the balls that include the pins. For a 2 inch use # 400B for nickel-plated steel, or # 401B for stainless steel. For 2-5/16 use # 600B for nickel-plated steel or # 601B for stainless steel.

expert reply by: Michael H

0

Answer 1

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 2

The #DM5939 is only compatible with the DA91 like the #DM8759131. Unfortunately, there is no option for manual lockout on a DA70 like the ##DM72VR. There are two ways you can keep your brakes from locking up with this brake actuator. The first is to…

view full answer...

Answer 3

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 4

Hello Richard, Great news, the Demco actuator you’re looking for is the right one. The Demco DA86 Trailer Brake Actuator for drum brakes, zinc, 2 inch ball, 8,600 lbs #DM98CV is Demco’s 8668601, so you’re on the correct track. I totally get wanting…

view full answer...

Answer 5

Hey Antanas, I went to the warehouse and measured for you. The Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #C69CR measures right at about 30" overall plug to plug. This is custom-made to fit the 2020…

view full answer...

Answer 6

There is a bulkhead underneath the 2015 Nissan Altima that will serve as a guide to line the hitch, #24796, up properly. Once the hitch is in place you will use it as a template to drill the holes needed for installation. I have included a link to…

view full answer...

Answer 7

I looked up what studs your UFP 10 inch hub/rotors should have and the the studs part #7-150 will work as a replacement. The spline diameter is .61 inch and overall is 2-1/4 inches so this would be a match. The diameter is also 1/2 inch like…

view full answer...

Answer 8

We have a few different lengths under the 1/2" - 20 wheel stud size so you'll wan to measure the length of what you currently have before ordering a replacement. 1-11/16" Long #K12WB169 1-7/8" #RG03-060 2" Long #K12WB2…

view full answer...

Answer 9

I was unable to see the photos you attached as it is blocked by our system but the casting numbers on your hubs are an old system that nobody goes by any longer. The brake assemblies with the welded backing plate have been outdated for decades and we…

view full answer...

Answer 10

I wish we had an easy solution, but we don't have magnets that will fit your application and we don't have a way to replace just the brake assemblies either as since what you have is welded directly to the trailer axle. So it will end up…

view full answer...

Answer 11

The thickness of the tube is not any different as they are both 3 inch diameter, and the spindles are also the same utilizing the same inner diameter bearings, hubs, and seals. The difference in capacity is in the custom bend in the axle that creates…

view full answer...

Replacement Pins and Balls for a Convert-A-Ball Interchangeable Ball Set

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching