See what our Experts say about this Convert-A-Ball Trailer Hitch Ball

• Will Draw-Tite Draw Bar Fit a Class I Draw-Tite Hitch on a 2023 Hyundai Elantra Hybrid
  Hey Hans, thanks for reaching out! Yes, the Drawbar for 1-1/4" Hitch # 36071 will fit with the Draw-Tite Sportframe Trailer Hitch Receiver # DT26PR (25006) on your 2023 Hyundai Elantra Hybrid. I'm not sure what hitch ball size you're needing, but if you aren't sure either then I recommend picking up the Convert-A-Ball Interchangeable Ball Set # 800B so you can tow a trailer that requires either a 1-7/8" or a 2" hitch ball size. If you don't already have wiring then I also recommend picking...
  view full answer...
• Tallest Rise 1-1/4 inch Hitch Ball Mount Availability
  When measuring for ball mount rise/drop needed you have to measure from the bottom lip of the coupler to the ground and not from the top like you mentioned. That means your trailer height is going to be more like 20 inches instead of 22 inches. That being said the closest ball mount we offer to what you need is going to be the part # C45028 which can do a rise of 5-3/8 inches. Then for a 2 inch ball you would want the part # C40018.
  view full answer...
• Interchangeable Hitch Ball and Ball Mount Recommendation for a 1-1/4 inch Hitch
  Sounds like you are looking for a multi-ball ball mount similar to the part # PS80425 but for a 1-1/4 inch hitch instead. I have a solution for you, but there are no ball mounts like that for the 1-1/4 inch hitches. Instead you would need a ball mount like the part # C45019 which fits 1-1/4 inch hitches and then an interchangeable ball set like part # 800B.
  view full answer...
• Class II Ball Mount And Interchangeable Hitch Ball For 2005 Ford Escape
  There aren't multi-ball ball mount options for a Class II hitch receiver, but I do have something to assist. I recommend the Draw-Tite Drawbar for 1-1/4" Hitch # 3593 along with the Convert-A-Ball Interchangeable Ball Set - 1-7/8", 2" Balls - 3/4" XL Shank - Nickel # 800B. This set does not have the 3rd hitch ball size of 2-5/16 inch because any coupler that will fit that ball size will be too heavy for your Class II Receiver.
  view full answer...
• Use One Ballmount to Tow Multiple Trailers - a 1-7/8 Inch and a 2 Inch Diameter Trailer Ball
  I would like to clarify some terminology so that we are on the same page, the hitch is the part attached to your 2008 Chevy Uplander. Then the ball mount or drawbar is attached to the hitch receiver using a pin and clip, or locking mechanism. Then the ball mount is outfitted with the appropriate size trailer ball. The diameter of the trailer ball shank needs to be compatible with hole the ball mount and the diameter of the trailer ball needs to be compatible with the trailer coupler. Since...
  view full answer...
• Can I Change My Trailer Coupler from a 1-7/8 Inch Coupler to a 2 Inch Coupler
  Rather than change the coupler, the easiest option is to change the size of the ball ON YOUR BALL mount. If your coupler currently uses a 1-7/8 inch ball and your towing vehicle has a hitch and ball mount with a 2 inch ball, you can use an interchangeable hitch ball system. This way you will not have to bother with changing the coupler on your jet ski trailer. If your current ball mount is compatible with a 3/4 inch diameter trailer ball shank then I recommend the # 800B, however if you...
  view full answer...
• Interchangeable Hitch Ball Set Compatible with 3/4 inch and 1 inch Drawbar Mounting Holes
  To be able to use a hitch ball with drawbars that have both a 3/4 inch and 1 inch shank you would need to select a hitch ball that has a 3/4 inch shank and then use a Hitch Ball Bushing, # C21100, that will reduce the size of the hole in the drawbar that accepts a 1 inch shank to 3/4 inch. You could use the Convert-A-Ball Interchangeable Ball Set, # 800B, along with the bushing in both drawbars and this would give you a 1-7/8 inch hitch ball and 2 inch hitch ball combination with 3,500...
  view full answer...
• Replacement Pins and Balls for a Convert-A-Ball Interchangeable Ball Set
  The internal pins in the balls are not available separately but you can replace the balls that include the pins. For a 2 inch use # 400B for nickel-plated steel, or # 401B for stainless steel. For 2-5/16 use # 600B for nickel-plated steel or # 601B for stainless steel.
  view full answer...
• Items Needed to Tow a Catalina 22 ft Sailboat
  The strongest trailer hitch that we have that is confirmed to fit the 1991 Toyota Previa is the Curt Trailer Hitch Receiver Custom Fit Class II - 1-1/4" # C12304. It has a Tongue Weight up to 300 pounds and up to 3500 pound Gross Towing Weight. The Curt Class II Drawbar # C45521 is what you need to go into the trailer hitch receiver to tow the trailer. Convert-A-Ball Interchangeable Ball Set # 800B comes with 1 7/8 and 2" balls with a 3/4 diameter shank and has a towing capacity of up...
  view full answer...
• Hitch for 2019 Toyota Camry to Tow Motorcycle Trailer with 565-lb Harley Davidson
  I'll start off by mentioning that from my research, it looks like the weight of the Stinger Folding motorcycle trailer you're looking at weighs in at around 220-lbs. When you add the 565-lb Harley to the trailer, you're looking at a total weight of a little less than 800-lbs. You'll want to consult your owner's manual for confirmation on the towing capacity of your 2019 Toyota Camry, but using the Curt # C11576 should allow you to tow that setup without any issues (I'm showing the towing...
  view full answer...
• Recommended Ball Mount and Hitch Ball for a 2012 Subaru Outback Wagon with 1-1/4 inch Receiver
  When measuring to see if you need a ball mount with a Rise or Drop you will want to make sure that your 2012 Subaru Outback Wagon is level and you will want to measure from the ground to the top of the trailer hitch receiver. For your trailer you will want to park it on level ground and measure from the ground to the bottom of the coupler. The difference between these 2 numbers will determine if you need a ball mount with a Rise or Drop. I have attached a helpful article and a picture to...
  view full answer...
  
• Recommendation for a Trailer Hitch for A 2006 Toyota Prius
  The trailer hitch recommended for your 2006 Toyota Prius is the Draw-Tite Sportframe Trailer Hitch # 24808. The Draw-Tite hitch is a custom-fit hitch that does not sacrifice on quality even though this hitch is the most cost efficient that we carry for the Prius. You need to note that the owner's manual for the 2006 Toyota Prius states that your vehicel is not recommended for towing and if you decided to tow with your Prius you will be towing at your own risk. If you decide to tow, then...
  view full answer...
• Ball Mount, Ball, and Trailer Wiring Harness Recommendations for a 2010 Honda CR-V
  I will be happy to get you the rest of the parts you will need to tow the rental trailer with your 2010 Honda CR-V. First for a ball mount we need to determine the hitch class you installed on your CR-V. Different hitch classes require different sized ball mounts and for the 2010 CR-V there are Class I and Class III hitches available. A Class I hitch will have a 1-1/4 inch receiver. A Class III will have a 2 inch receiver opening. If you have a Class III hitch with a 2 inch opening I recommend...
  view full answer...
• Which Receiver Has Best Height and Bumper Clearance for 2016.5 Mazda CX-5
  The Curt Trailer Hitch Receiver Item # C12170 is the hitch recommended to tow your small lightweight boat. It has a 1 1/4" receiver opening and is a confirmed fit for your 2016.5 Mazda CX-5. it has a maximum gross trailer weight of up to 3,500 lbs and a maximum tongue weight of up to 350 lbs. (Be sure to check your owners manual for vehicle towing specs). The Curt Trailer Hitch Receiver has great clearance. From the center of the hitch pin hole to the outermost edge of the bumper right...
  view full answer...
• 1-7/8 Inch Hitch Ball Recommendations with 3/4 Inch Shank Diameter and at Least 3,500 lbs Capacity
  You could use the Convert-A-Ball Interchangeable Ball Set # 800B that has a capacity of 3,500 lbs. I attached an FAQ on hitch balls for you to check out also.
  view full answer...
• Recommendations For Outfitting A 2008 Subaru Forester To Tow A Trailer
  Though the size of the ball and amount of rise or drop for the ball mount will be determined by the size of the trailer coupler and how high it is off the ground, I can definitely make a few suggestions for you. To start with, the Curt # C12038 will be the hitch I recommend. You will need to double check your owner's manual to verify the vehicle capacities, but this will be rated up to 3,500 pounds towing and 350 pounds of tongue weight. Once installed, the top of the receiver opening...
  view full answer...
• Replacement Westin Bumper Install Kit for 1991 Chevrolet S-10
  The Westin Fey Surestep Rear Bumper # 76001 requires custom install brackets and will not fit your current stock bracket. The kit for your 1991 Chevrolet S-10 that includes the bumper, brackets, and hardware is # 76001-97200. For hitch balls you'll need a 3/4 inch shank. The Tow Ready 1-7/8 inch is # 19256 and the 2 inch is # 19258. Of if you'd like one interchangeable ball, the Convert-A-Ball # 800B can work as either.
  view full answer...
• Converting From 1 inch Shank Convert a Ball Interchangeable Ball Set to 3/4 inch Shank
  For a replacement 3/4 inch diameter shank for the Convert-a-Ball interchangeable hitch balls you'd want the part # 104B and you'd be set. The balls are the same so what you have now would work with this.
  view full answer...
• Can Shank Included w/ Convert-A-Ball # 800B Be Used With a 2-5/16 Inch Trailer Ball
  The 2-5/16 ball will fit on the shank of the # 800B, but because the shank portion uses a 3/4 inch threaded shank, it's not strong enough to tow a trailer large enough to be rated for a 2-5/16 inch ball. However, if you're just moving the trailer a few feet on flat ground, you can use a standard 2 inch ball of any kind if you wish.
  view full answer...
• Is Ball on Curt # C45571 Euro-Style Ball Removable
  The Curt Euro-Style Class II ball mount you referenced, part # C45571 features a permanently attached 1-7/8 inch trailer ball which is not removable. If you were wanting a ball mount with a similar rise where you could interchange the trailer ball, I'd recommend going with a standard type ball mount, like part # C45017. If you anticipate needing to change between 1-7/8 and 2 inch trailer balls frequently, I'd recommend using a interchangeable ball set-up like what Convert-A-Ball offers....
  view full answer...
• Recommended Multi-Ball Hitch Ball For 2005 PT Cruiser Hitch
  For your Class I Hitch Receiver # C11132, I do have a multi-ball option for you. To go with the ball mount # 3593, I recommend the Convert-A-Ball Interchangeable Ball Set - 1-7/8", 2" Balls - 3/4" XL Shank - Nickel # 800B. This allows you to simply replace the ball with the larger or smaller diameter ball and everything else remains in place. You won't need the largest size hitch ball as your vehicle can't tow anything that would require the 2-5/16 inch ball and there isn't one available...
  view full answer...
• Cover for Upper Shank on Interchangeable Ball Sets
  We do have a cover for certain interchangeable ball sets. It is Convert-a-Ball Cover for Interchangeable Shank Item # 005B. It is designed to fit Convert-A-Ball systems though. So what I recommend is to use Convert-A-Ball Interchangeable Ball Set - 1-7/8", 2" Balls - 3/4" XL Shank - Nickel Item # 800B. I have linked a video review for you.
  view full answer...
• Do you Carry a 1-7/8" Hitch Ball With 3/4" Shank and 2" Rise?
  While we do not carry any 1-7/8" balls with a 3/4" shank and a 2" rise we do have the 1-7/8" Hitch Ball # 19254 which has a 3-3/8" long, 3/4" shank. This would allow you to have a spacer machined to give you the rise you are looking for.
  view full answer...
• Diameter of the Pin of the Convert-A-Ball part # 800B
  The pin that runs down the middle of the balls on the Convert-A-Ball part # 800B measures 7/16 of an inch in diameter.
  view full answer...