Is Blue Ox SwayPro Weight Distribution Compatible with Aluminum Trailer Frame

Question

Question:

Hi, I will be towing a small vehicle on an all aluminum open trailer. Can I use this product on an aluminum trailer tongue? Specifically clamping the distribution mounts onto the trailer tongue. Does the trailer have to be steel? Best,

asked by: Matt

0

Expert Reply:

I reached out to my contact at Blue Ox who said that they don't have any stipulations about using the Blue Ox SwayPro Weight Distribution w/ Sway Control # BXW0350 with an aluminum frame trailer. Just note that you also need a hitch ball with this setup like the 2" # A-90 or the 2-5/16" # 19286. You also want to make sure that the loaded tongue weight of your trailer plus the weight of any cargo behind the rear axle of your tow vehicle doesn't exceed the 350 lb tongue weight rating for this system. Since you mentioned hauling a car you likely need to upgrade to the next size up, part # BXW0550, which has a tongue weight range of 350 lbs - 550 lbs.

Even though Blue Ox doesn't have a problem with you using this system on an aluminum frame trailer, the trailer manufacturer will be the one to have the final say on whether that is okay or not because aluminum frames have a reputation of not holding up well with a weight distribution system. If your manufacturer says not to use weight distribution then the next best thing is to add suspension enhancement to your tow vehicle. Let me know the year/make/model of your tow vehicle in this case and I can make a recommendation for you.

expert reply by: Jon G

0

Answer 1

Hey Justin, thanks for reaching out. We can definitely get you a weight distribution hitch for your 2026 Jayco Jay Flight SLX 170BH, but the Curt #C69JR you mentioned is a bit overrated for that setup. That is for trailers with a tongue weight…

view full answer...

Answer 2

Hey Jeff, I looked up the weight of an Intech Flyer Explore relative to the towing capacity of your 2009 Nissan Xterra and you'd be right at where I would start to strongly recommend a weight distribution system. I won't lie to you and tell…

view full answer...

Answer 3

When it comes to replacing your spring bars you need to first know what the tongue weight rating is for your current system. The bars will have dimples on them which will tell you what your tongue rating is. Any of the following bars will work for…

view full answer...

Answer 4

Hey Mike! We do have an option that weighs less than 70 lbs. The Blue Ox SwayPro Weight Distribution w/ Sway Control for 2" Hitch #BXW0550 weighs 50 lbs. This is designed to work with trailer tongue weights ranging from 350 lbs - 550 lbs. If you…

view full answer...

Answer 5

It is usually possible to replace the spring bars in a weight distribution hitch setup so long as the two sets of bars are the same type, both trunnion style for instance, and both are from the same generation of hitch. A 10-year-old setup may not be…

view full answer...

Answer 6

Hey Mark, welcome back! This is very much a case of "you get what you pay for." The Curt TruTrack 2P #C95MJ you looked at is a good option if you tow your trailer a short distance once or twice a year. If you tow with any frequency and you…

view full answer...

Answer 7

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 8

Hey Michael! When you're choosing a weight distribution hitch the most important factor is the tongue weight of the trailer. It looks like the dry/unloaded tongue weight of a Brinkley Z Air 297 is 924 lbs. Once you add batteries and propane you…

view full answer...

Answer 9

Hey, Daniel. Thanks for your question. We do have a weight distribution hitch that would work for your trailer and still use chains. That hitch is the Blue Ox SwayPro #BXW0350. The tongue weight rating needed for this system to work is between…

view full answer...

Answer 10

Hey Jeff! Yes, we do have a hitch and wiring for your 2027 Crown Signia. For the hitch I recommend the Curt Trailer Hitch Receiver #C35MJ. This is a Class III hitch with a 2" receiver and a bolt-on installation. Then for wiring you can use the…

view full answer...

Answer 11

Hey Leonard! Yes, you can use the hitch pin hole furthest away from the head to install the Andersen Weight Distribution Hitch #AN53VR in your receiver. Both of the hitch pin holes can be used to secure the shank. What kind of trailer are you…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is Blue Ox SwayPro Weight Distribution Compatible with Aluminum Trailer Frame

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching