Can Bulldog Coupler # BD43805W0317 be Bolted and then Welded On

Question

Question:

Can I drill 1/2 inch holes and bolt this on, then weld on

asked by: Timothy W

0

Expert Reply:

Yes, if you wanted to first bolt the Bulldog Heavy-Duty Cast Head Coupler # BD43805W0317 to your trailer and then weld it after you certainly could.

expert reply by: Jameson C

0

Answer 1

Hello John, thanks for reaching out. I went out to our warehouse and measured the Bulldog Heavy-Duty Cast Head Coupler #BD43805W0317. The bolt holes are 3" apart on center. I edited a picture for you. The 3" hole spacing is standard for…

view full answer...

Answer 2

Bulldog A-frame trailer coupler #BD43805W0317 does not have holes on the side because it is a weld-on coupler. Coupler #BD44150WH301 can be bolted on but it is for a 2-5/16 inch ball, not a 2 inch ball like #BD43805W0317. All of the other A-frame…

view full answer...

Answer 3

The most comparable replacement for your Fulton model 0926012 3K capacity A-frame trailer jack would be the Bulldog #BD1550101344 which offers the same capacity and amount of lift as your current jack. The jack features a zinc finish that offers good…

view full answer...

Answer 4

The bolt pattern used on the Bulldog Jack BD195318 is a little different than most, but I did include a diagram showing how it measures. The outer tube will measure 2-1/4" x 2-1/4" and the inner tube is 2" x 2" . From the bottom…

view full answer...

Answer 5

I can help you understand the difference between the latch lock style for couplers and the collar lock style. First let's talk about the latch style. If installed properly this style of coupler will work great. Determining if it is latched…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Can Bulldog Coupler # BD43805W0317 be Bolted and then Welded On

Continue Researching