Is There a Replacement Wheel Bracket for the Fulton F2 Swing-Up Trailer Jack

Question

Question:

So i was pushing a trailer and i broke the wheel casing off the end of my jack. The wheel is ok, but the mounting case for the wheel is broken. Can i replace that part or do i need to get a new jack?

asked by: Donald

0

Expert Reply:

The wheel housing is not replaceable on the Fulton F2 Swing-Up Trailer Jack so your only option is a new jack, the Fulton F2 Swing-Up Trailer Jack part # F1413050334 which has a 1,600 lb weight capacity.

expert reply by: Conner L

0

click to enlarge

Answer 1

Aside from the weight capacity of the jacks and their speed, they also have different mounting bracket locations. If you don't mind potentially having someone do some cutting and welding on your trailer then either one will work great for you. If…

view full answer...

Answer 2

Most likely you need to go with the Reese Landing Gear Set #RP500708 because it has the typical inside to inside and outside to outside spacing of 15-1/2" and 17-1/2" respectively. This is the most common weld stop measurements which is why…

view full answer...

Answer 3

While I don't know exactly what landing gear you have on your 2011 Keystone Raptor 3812 Toy Hauler, I can say that you should be able to replace them with the Landing Gear Set w/ Handle #RVLG-8HDL as this landing gear uses the standard weld mount…

view full answer...

Answer 4

I spoke with my contact at Fulton and he confirmed that both the Fulton XLT #F141133 and the F2 Swing-Up #F1413040134 will fit your trailer frame that measures 3 inches x 1-1/2 inches. Typically bracket height is measured from the bottom of the wheel…

view full answer...

Answer 5

I went out to the warehouse and pulled one of the Pro Series Snap-Ring Swivel Jacks, #PSEJ10000101, to measure for you. I added dimensions to a photo I took of the mounting plate for you to use to see if the mounting pattern will match up to your…

view full answer...

Answer 6

Hey George, thanks for the pictures and congrats on the new boat. The The mount used by your Dutton-Lainson jack wouldn't be compatible with the Fulton F2 or any other brand of jack for that matter. This leaves you with a couple of options. The…

view full answer...

Answer 7

The Fulton F2 trailer jack #F1413040134 will only fit 3 x 3 inch and 3 x 4 inch trailer frames. What you will need is a weld-on model, #F1413050334. It will fit a trailer frame that is 3 inches tall or more. The plate will need to be welded to the…

view full answer...

Answer 8

Thanks for the photo. The Fulton F2 jacks use a different mount so it isn't compatible with your current base. You will need to remove the base and then you can install the F2 #F1413040134 you referenced. This F2 will come with all new mounting…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Is There a Replacement Wheel Bracket for the Fulton F2 Swing-Up Trailer Jack

Continue Researching